Forum Discussion

Jim_L's avatar
Jim_L
Level 3
13 years ago

Backup Exec 12.5 Sometimes Slow

We are using BE 12.5 to backup about 1TB of data D2D using USB drives. About 60% of the time the backup is quick, 2000MB/min. or faster, but occasionally it runs under 1,000MB/min. and doesn't complete in under 24 hours. I have found no correlation between the slow backups and which physical USB drive we use or which USB 3.0 port we use. The drives are all USB 3.0. The most recent backup that was running was pegging CPU utilization on one core of the server for bengine.exe. It also seemed like Kernel memory utilization was high at around 300MB. I have tried defragmenting the .bkf file, but that seems to make no difference. I checked a few drives and natively I can copy large files to the drives well over the 2000 MB/min. we get on a quick backup, so it doesn't look like a drive throughput issue. Other than upgrading to a newer version of BE, is there something else I should try? Thanks,

Jim

12.x and Earlier
Backing Up
Backup and Recovery
Backup Exec
Basics
Configuring
Performance
Troubleshooting
  • CraigV's avatar
    CraigV
    13 years ago

    ...it's a very fine line to get this right. Make your size too big and you risk losing a lot of data if 1 *.bkf file is corrupt, and you MIGHT have speed issues; make the size too small and you're going to build up a lot of small files which might also impact speed.

    Just ensure that your AV is also not scanning your dedupe folder!

  • CraigV's avatar
    CraigV
    Moderator
    13 years ago

    Hi,

     

    Turn off (put in exclusions) for the B2D folders and the BE services, and make sure your slow backups aren't being done during some sort of maintenance (AV scan for example).

    Also, I take it you defragged the whole drive...not just the B2D file? What size have you set them too as well?

    Thanks!

  • Jim_L's avatar
    Jim_L
    Level 3
    13 years ago

    Hi Craig,

    We intentionally do not have any anti-virus locally on the server we use for BE. I also checked to make sure there aren't any conflicting Scheduled Tasks, which there aren't. I have looked for patterns, such as day of the week, physical drive, USB 3.0 port or USB cable, but can't find a pattern.

    I just recreated a B2D drive from scratch to make sure it isn't a fragmentation issue and I am testing it currently. They can grow up to 1,800 GB. The backup is typically just over 1TB. Thansk,

    Jim

     

  • CraigV's avatar
    CraigV
    Moderator
    13 years ago

    ...not capacity of the B2D folder, the size of each B2D file that BE creates. The standard is 4GB but this can be set. If you're creating 1 large 1800GB file you're going to run into issues. if that file corrupts you'd kiss all your data goodbye.

    Some recommend no larger than 50GB for a B2D file before BE creates another...

  • Jim_L's avatar
    Jim_L
    Level 3
    13 years ago

    This BE server is setup to create a single file, typically 1 TB. If that is an issue I will reconfigure one of the disk to test smaller B2D files. I inherited this server as it is setup currently. Thanks for the advice.

  • AmolB's avatar
    AmolB
    Moderator
    13 years ago

    Hello Jim

      Below TN explains how to find B2D file size and how to change the file size too.

      http://www.symantec.com/docs/TECH35131

  • Jim_L's avatar
    Jim_L
    Level 3
    13 years ago

    Hello Amol,

    Thanks for the link!

    I have completed 2 backups since limiting the file size to 100 GB. One backup averaged 1.4 GB/min and the one today averaged 2.5 GB/min. This is typical that the backup rate can vary so widely and things like enabling or disabling compression have not made a difference.  Some of the things I have tried to resolve the highly variable backup rates without success:

    • Turn compression off, it was on
    • Defragment USB backup drives before backup job starts
    • Restart all BE services between backup jobs
    • Reboot backup server between backup jobs
    • Update BE software for latest patches for 12.5
    • Always use the same USB 3.0 port
    • Try different USB ports
    • Update backup server software with latest updates from Microsoft
    • Update BE agent on servers being backed up

    I am not sure what to try next. Verification is always very speedy, so it seems to either be an issue with reading the files from the remote servers or with writing the files to the USB drive. I have seen pretty high numbers for disk queue length on the USB drive when a backup is taking place.

  • CraigV's avatar
    CraigV
    Moderator
    13 years ago

    ...any reason for you having a 100GB B2D file size and not trying something like 20/50/65GB for instance?

    Drop the file size smaller and see if this resolves the issue.

    Thanks!