Unable to use vcs commands after installation of vcs

Question

Hi,

&nbsp;

After installation of VCS 6.0 in Sol10,I am unable to run even hastatus -sum command it says, command not found however, llttab shows the O/p as

bash-3.00# cat /etc/llttab
	set-node papa
	set-cluster 37074
	link e1000g0 /dev/e1000g:0 - ether - -
	link e1000g1 /dev/e1000g:1 - ether - -
	link-lowpri e1000g2 /dev/e1000g:2 - ether - -

=====================================

bash-3.00# cat /etc/gabtab
	/sbin/gabconfig -c -n1

============================

checked with pkginfo,

bash-3.00# pkginfo |grep vcs
	system &nbsp; &nbsp; &nbsp;VRTSvcs &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;Veritas Cluster Server by Symantec
	system &nbsp; &nbsp; &nbsp;VRTSvcsag &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;Veritas Cluster Server Bundled Agents by Symantec
	system &nbsp; &nbsp; &nbsp;VRTSvcsea &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;Veritas High Availability Enterprise Agents by Symantec

============================================================================

bash-3.00# df -h
	Filesystem &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; size &nbsp; used &nbsp;avail capacity &nbsp;Mounted on
	/dev/dsk/c1t0d0s0 &nbsp; &nbsp; &nbsp; 14G &nbsp; 2.3G &nbsp; &nbsp;12G &nbsp; &nbsp;17% &nbsp; &nbsp;/
	/devices &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; 0K &nbsp; &nbsp; 0K &nbsp; &nbsp; 0K &nbsp; &nbsp; 0% &nbsp; &nbsp;/devices
	ctfs &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; 0K &nbsp; &nbsp; 0K &nbsp; &nbsp; 0K &nbsp; &nbsp; 0% &nbsp; &nbsp;/system/contract
	proc &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; 0K &nbsp; &nbsp; 0K &nbsp; &nbsp; 0K &nbsp; &nbsp; 0% &nbsp; &nbsp;/proc
	mnttab &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; 0K &nbsp; &nbsp; 0K &nbsp; &nbsp; 0K &nbsp; &nbsp; 0% &nbsp; &nbsp;/etc/mnttab
	swap &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; 2.2G &nbsp; 1.1M &nbsp; 2.2G &nbsp; &nbsp; 1% &nbsp; &nbsp;/etc/svc/volatile
	objfs &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;0K &nbsp; &nbsp; 0K &nbsp; &nbsp; 0K &nbsp; &nbsp; 0% &nbsp; &nbsp;/system/object
	sharefs &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;0K &nbsp; &nbsp; 0K &nbsp; &nbsp; 0K &nbsp; &nbsp; 0% &nbsp; &nbsp;/etc/dfs/sharetab
	/dev/dsk/c1t0d0s5 &nbsp; &nbsp; &nbsp;9.6G &nbsp; 4.3G &nbsp; 5.3G &nbsp; &nbsp;45% &nbsp; &nbsp;/usr
	/usr/lib/libc/libc_hwcap1.so.1
	&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;9.6G &nbsp; 4.3G &nbsp; 5.3G &nbsp; &nbsp;45% &nbsp; &nbsp;/lib/libc.so.1
	fd &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; 0K &nbsp; &nbsp; 0K &nbsp; &nbsp; 0K &nbsp; &nbsp; 0% &nbsp; &nbsp;/dev/fd
	/dev/dsk/c1t0d0s3 &nbsp; &nbsp; &nbsp;1.9G &nbsp; &nbsp;93M &nbsp; 1.7G &nbsp; &nbsp; 5% &nbsp; &nbsp;/var
	swap &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; 2.2G &nbsp; &nbsp;44K &nbsp; 2.2G &nbsp; &nbsp; 1% &nbsp; &nbsp;/tmp
	swap &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; 2.2G &nbsp; &nbsp;32K &nbsp; 2.2G &nbsp; &nbsp; 1% &nbsp; &nbsp;/var/run
	/dev/dsk/c1t0d0s4 &nbsp; &nbsp; &nbsp;2.9G &nbsp; 819M &nbsp; 2.0G &nbsp; &nbsp;29% &nbsp; &nbsp;/opt
	/dev/dsk/c1t0d0s6 &nbsp; &nbsp; &nbsp;103M &nbsp; 1.0M &nbsp; &nbsp;92M &nbsp; &nbsp; 2% &nbsp; &nbsp;/temp
	/dev/dsk/c1t0d0s7 &nbsp; &nbsp; &nbsp; 18G &nbsp; &nbsp;19M &nbsp; &nbsp;18G &nbsp; &nbsp; 1% &nbsp; &nbsp;/export/home
	/vol/dev/dsk/c0t0d0/sol_10_910_x86
	&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;2.0G &nbsp; 2.0G &nbsp; &nbsp; 0K &nbsp; 100% &nbsp; &nbsp;/cdrom/sol_10_910_x86
	/dev/odm &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; 0K &nbsp; &nbsp; 0K &nbsp; &nbsp; 0K &nbsp; &nbsp; 0% &nbsp; &nbsp;/dev/odm
	/dev/vx/dsk/datadg/datavol
	&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;200M &nbsp; 103M &nbsp; &nbsp;91M &nbsp; &nbsp;54% &nbsp; &nbsp;/pictor

==========================================================

&nbsp;

bash-3.00# vxdisk list
	DEVICE &nbsp; &nbsp; &nbsp; TYPE &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;DISK &nbsp; &nbsp; &nbsp; &nbsp; GROUP &nbsp; &nbsp; &nbsp; &nbsp;STATUS
	disk_0 &nbsp; &nbsp; &nbsp; auto:none &nbsp; &nbsp; &nbsp; - &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;- &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;online invalid
	disk_1 &nbsp; &nbsp; &nbsp; auto:none &nbsp; &nbsp; &nbsp; - &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;- &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;online invalid
	disk_2 &nbsp; &nbsp; &nbsp; auto:cdsdisk &nbsp; &nbsp;datadg01 &nbsp; &nbsp; datadg &nbsp; &nbsp; &nbsp; online
	disk_3 &nbsp; &nbsp; &nbsp; auto:cdsdisk &nbsp; &nbsp;datadg02 &nbsp; &nbsp; datadg &nbsp; &nbsp; &nbsp; online

&nbsp;

PLease help..

&nbsp;

mikebounds · Answer

hastatus command is in /opt/VRTSvcs/bin and there is a sym link in /opt/VRTS/bin, so add either of these to your path or specify complete path. I would advice adding /opt/VRTS/bin to your path:

export PATH=$PATH:/opt/VRTS/bin

Mike

export PATH=$PATH:/opt/VRTS/bin

Mike

marianne · Answer

'command not found' is a Unix error, saying that the current shell cannot find the command in your PATH variable.

You will find this recommendation in the sfha_install guide (Add the paths to your .profile to make it permanent):

Setting environment variables
	Most of the commands used in the installation are in the /sbin or /usr/sbin
	directory. Add these directories to your PATH environment variable as necessary.
	After installation, SFHA commands are in /opt/VRTS/bin. SFHA manual pages
	are stored in /opt/VRTS/man.
	
	Add the following directories to your PATH and MANPATH environment variable:
	
	■ If you are using Bourne or Korn shell (sh or ksh), enter the following:
	$ PATH=$PATH:/usr/sbin:/opt/VRTS/bin
	$ MANPATH=/usr/share/man:/opt/VRTS/man:$MANPATH
	$ export PATH MANPATH
	
	■ If you are using a C shell (csh or tcsh), enter the following:
	% set path = ( $path /usr/sbin /opt/VRTS/bin )
	% setenv MANPATH /usr/share/man:/opt/VRTS/man:$MANPATH

gaurav_singh · Answer

Thanks marianne.. got it and issue is resolved.

Forum Discussion

Unable to use vcs commands after installation of vcs

Related Content

command: bperror

Unable to install Netbackup 9.1.0.1 client on Linux

CLI Command to list Host ID

Monitoring nbpemreq command

Unable to Install Netbackup

Recent Discussions

Configuring SQL Server in a VMware environment?

Configure two Mount type resources of nfs FStype attribute using the same share

order

key registration and reservation

Verifying that primary and dr clusters replication is synced