NBU 7.5 Recommended device drivers for IBM LTO4 tape drives

Question

What is the recommended device drivers for IBM LTO4 drives with NetBackup 7.5.0.6 ?
SAN media server is HP server - W2008 R2 Service Pack 1
Currently using IBM driver 6.2.3.6
&nbsp;
Symptoms:
When Media server&nbsp;are bounced - it does not go down UNTIL the drives are being Disabled via the Device manager.
When Enabling the drives again it takes very very long.
&nbsp;
Any advise?
&nbsp;
&nbsp;

sksujeet · Answer

It is recommended to use latest drivers of the Vendor
When Media server&nbsp;are bounced - it does not go down UNTIL the drives are being Disabled via the Device manager.
YOu mean you are not able to power dow the server if the drivers are enabled? Which OS and hardware you are running.
Gracefull shutdown of server which is very busy or running appliation will take some time to disconnect all the connection and will shut down. How long you waited and what it generates in the event viwer

marianne · Answer

According to NBU 7.x HCL, Symantec has tested driver version&nbsp;6.2.1.7.
There are also other instructions for IBM tape drivers in the HCL:
IBM Tape Driver Support
The latest version of the IBM tape device driver package that has been tested with NetBackup is listed below. Using the version listed here is recommended, but older versions of the tape drivers are also supported and may work well. There is no need to upgrade the tape driver if the configuration is working properly. Upgrading to the version listed here may be necessary if implementing the latest model tape drives or if problems are encountered that have been addressed by the driver provider.

If using the IBM Windows Tape Device Drivers be sure to choose the install_nonexclusive.exe executable. This option permits a tape drive to be accessed by multiple processes on a Media Server, which is a requirement for NetBackup.
NetBackup requires the IBM Data Path Failover feature to be disabled on the IBM tape device driver. To disable this feature, open the reg folder of the IBM driver package, double-click DisableDPF.reg, and reboot the system.
- IBMTape driver level 6.2.1.7 tested on Windows
&nbsp;
&nbsp;
Please also check HBA make/model/driver - IBM should have a compatibility matrix on their web site.
	Confirm that tape and disks are zoned to different HBA's.
Some HBA vendors have recommended settings for use with tape.
	These recommendations can usually be found on the vendor's web site.
&nbsp;
Hope this helps!

willie_sa · Answer

Thank you for the replies.
The claim was made that when the server was restarted(down and up)&nbsp;normally - it did not go down - until they went in again in safe mode and disabled the drives. This was after 30 minutes.
&nbsp;
My experience - on the side to enable the drives again.
I enable via the Server Manager / Device monitor.
It takes +- 15 minutes for the screen to return from hour glass. When you then close the window and open again - the drive is enabled.
During the 'enable time' you cannot do anything in that Server Manager window.
It is as if the Enable process takes _= 15 minutes to complete the enable process.
&nbsp;
&nbsp;

marianne · Answer

Maybe uninstall and reinstall drivers as per above documentation?
When system is accessible again, check Windows Event logs for errors during period that problems were experienced - especially System log.
Please check hba drivers/settings as well.&nbsp;

willie_sa · Answer

I uninstalled the drivers.
When re-installing with command _exclusive or _nonexclusite _ it times out. Coming up with message:
Exiting application.
Program stopped prematurely due to error(s).
	If the debug flag was set, check debug.txt for details.

Forum Discussion

NBU 7.5 Recommended device drivers for IBM LTO4 tape drives

Related Content

What is a driver, device file, device path in netbackup

Symantec Device Drivers for IBM Tape Drives

Device Driver for IBM Ultrium TD3

Recommended Encryption option for NBU Appliance??

Windows Tape Device Drivers