cancel
Showing results for 
Search instead for 
Did you mean: 

failed to bring up HeartBeat interface with GAB config

MahmoudHafez
Not applicable

Dear Experts,

   I'm facing an issue here in cluster setup 8+2 

I have managed to create 1+1 cluster and when trying to add the 3rd node I got stuck in gabconfig step 

below is the /var/adm/messages 

Jun 21 22:49:50 MM-BL2 bnxe: [ID 801725 kern.info] NOTICE: bnxe3: BnxeHwStartCore: Starting hardware (clients None)
Jun 21 22:49:51 MM-BL2 bnxe: [ID 801725 kern.info] NOTICE: bnxe3: Phy capabilities (1) (supported 0x00000f50 0x00000000) (link_config 0x01000000 0x00000000)
Jun 21 22:49:51 MM-BL2 bnxe: [ID 801725 kern.warning] WARNING: bnxe3: Phy 10000fdx requested but not supported
Jun 21 22:49:51 MM-BL2 bnxe: [ID 801725 kern.info] NOTICE: bnxe3: Phy requesting link config of 0x00000006
Jun 21 22:49:51 MM-BL2 bnxe: [ID 801725 kern.info] NOTICE: bnxe3: 10Gb Full Duplex Rx Flow ON Tx Flow ON Link Up
Jun 21 22:49:51 MM-BL2 bnxe: [ID 801725 kern.info] NOTICE: bnxe3: BnxeHwStartCore: Hardware started (clients None)
Jun 21 22:49:51 MM-BL2 bnxe: [ID 801725 kern.info] NOTICE: bnxe3: BnxeHwStartL2: L2 started (clients L2)
Jun 21 22:49:51 MM-BL2 bnxe: [ID 801725 kern.info] NOTICE: bnxe3: BnxeHwStopL2: Stopping L2 (clients L2)
Jun 21 22:49:51 MM-BL2 bnxe: [ID 801725 kern.info] NOTICE: bnxe3: BnxeHwStopCore: Stopping hardware (clients None)
Jun 21 22:49:51 MM-BL2 bnxe: [ID 801725 kern.info] NOTICE: bnxe3: Link Down
Jun 21 22:49:51 MM-BL2 bnxe: [ID 801725 kern.info] NOTICE: bnxe3: BnxeHwStopCore: Hardware stopped (clients None)
Jun 21 22:49:51 MM-BL2 bnxe: [ID 801725 kern.info] NOTICE: bnxe3: BnxeHwStopL2: L2 stopped (clients None)
Jun 21 22:49:51 MM-BL2 bnxe: [ID 801725 kern.info] NOTICE: bnxe3: BnxeHwStartL2: Starting L2 (clients None)
Jun 21 22:49:51 MM-BL2 bnxe: [ID 801725 kern.info] NOTICE: bnxe3: BnxeHwStartCore: Starting hardware (clients None)
Jun 21 22:49:52 MM-BL2 bnxe: [ID 801725 kern.info] NOTICE: bnxe3: Phy capabilities (1) (supported 0x00000f50 0x00000000) (link_config 0x01000000 0x00000000)
Jun 21 22:49:52 MM-BL2 bnxe: [ID 801725 kern.warning] WARNING: bnxe3: Phy 10000fdx requested but not supported
Jun 21 22:49:52 MM-BL2 bnxe: [ID 801725 kern.info] NOTICE: bnxe3: Phy requesting link config of 0x00000006
Jun 21 22:49:52 MM-BL2 bnxe: [ID 801725 kern.info] NOTICE: bnxe3: 10Gb Full Duplex Rx Flow ON Tx Flow ON Link Up
Jun 21 22:49:52 MM-BL2 bnxe: [ID 801725 kern.info] NOTICE: bnxe3: BnxeHwStartCore: Hardware started (clients None)
Jun 21 22:49:52 MM-BL2 bnxe: [ID 801725 kern.info] NOTICE: bnxe3: BnxeHwStartL2: L2 started (clients L2)
Jun 21 22:49:53 MM-BL2 bnxe: [ID 801725 kern.info] NOTICE: bnxe3: BnxeHwStopL2: Stopping L2 (clients L2)
Jun 21 22:49:53 MM-BL2 bnxe: [ID 801725 kern.info] NOTICE: bnxe3: BnxeHwStopCore: Stopping hardware (clients None)
Jun 21 22:49:53 MM-BL2 bnxe: [ID 801725 kern.info] NOTICE: bnxe3: Link Down
Jun 21 22:49:53 MM-BL2 bnxe: [ID 801725 kern.info] NOTICE: bnxe3: BnxeHwStopCore: Hardware stopped (clients None)
Jun 21 22:49:53 MM-BL2 bnxe: [ID 801725 kern.info] NOTICE: bnxe3: BnxeHwStopL2: L2 stopped (clients None)

 

 

knowing that I have the same network profiles interfaces for all blades ( HP Proliant blades ) 

any ideas how this can be fixed ? 

 

BR

Mahmoud 

1 REPLY 1

Gaurav_S
Moderator
Moderator
   VIP    Certified

Can you elaborate on the steps you have followed ? What version of VCS & OS ?

Have you modified the LLT & GAB configuration files ?

 

G