Exchange Serve 2010 Backup of Databases and Restore to RDB
Today we are going to discuss the databases of Exchange 2010 HA Backup and Restore Activity. In this Activity we will discuss how to take the Backup of Exchange 2010 Databases and Restore in RDB in a Exchange 2010 HA scenario.
In this discussion we will also try to cover the basic steps which required starting the Backup of Exchange2010 databases. The Steps will cover the Attributes, Clients and Backup Selections TAB in the NetBackup Policy for Exchange 2010.
NetBackup Server = 7.1
OS of NetBackup Server = Win2008 R2
NetBackup Clients = 7.1
OS of NetBackup Clients = Win2008 R2
Clients product which’s backup will be perform = Exchange Server 2010 (two nodes) under HA
Exchange 2010 HA Details
Exchange Server Node1 has a database (DB1) of let suppose 50Mailboxes.
Exchange Server Node2 has a database (DB2) of let suppose 50 other Mailboxes.
Exchange Server node1 replicating its database to Exchange Server node2 (replicating not on/over node2 DB)
Exchange Server node2 replicating its database to Exchange Server node1 (replicating not on/over node1 DB)
See the below SNAP for reference of the Exchange2010 HA scenario in which both databases backup we will take via NetBackup Server.
The above snap is just to show as an example so that all can understand what is the scenario. Imagine that each Exchange 2010 hosts one Database.
Exchange 2010 Backup
Before going to start the Backup Activity stop the firewall on both Nodes of Exchange 2010 machines (Does not stop the firewall from the Administrative Tools=>Services. This will disconnect you machine from Network). See the below SNAP for your reference. Select the RED highlighted box and click on OK:
Open the below ports in case to keep the OS Firewall ON. or your Exchange 2010 Nodes are behind Network/etc Firewall.
Now let we start creating the Backup Policy for Exchange Databases.
Open NetBackup Console=>Right Click on Policy=>New=>Policy Name=>Click OK and you will find a below window
NetBackup Server uses this option when NetBackup takes the backup of Database from the Active Database. The Active Database is the Active copy of Database not the replicated copy. We use this option when we may have single machine and there is no replicated copy or no replication scenario and the Exchange2010 is on single Node.
Passive Copy Only
NetBackup Server uses this option when NetBackup takes the backup of Database from the Passive Database. The Passive Database is the Passive copy of Database which is the replicated copy.
Passive Copy and if not available the Active Copy
NetBackup Server uses this option when NetBackup takes the backup of Database from the Passive Database and if for some reason the Passive Copy is not available the NetBackup will take the Backup from the Active Copy of Database.
The above things we discussed from the Attributes TAB of Exchange 2010 Policy and now we will move forward towards the Clients and Backup Selections TAB. The Schedule TAB is same as others so we will not discuss this in our conversation.
NetBackup asks the databases from the virtual DAG and it(virtual DAG connect the session with the databases)
I hope this is enough to understand the Client TAB role in the Exchange 2010 Backup Policy. See the below SNAP for reference:
The Backup Policy is ready to trigger. Start the VERITAS NetBackup Server Policy for Exchange which starts picking the Backup.
Exchange 2010 Restore
Above we took two databases backup and now we do a Restore Activity of one Database from the Two databases Backup through which we will sure that our Backup was successful. There are multiple ways to Recover t he Exchange Server but it depends on what type of disaster happened. So in the below Activity we will do the Recovery of Database to the Recovery Database “RDB.”.
So now let’s start the Exchange 2010 recovery of Database which backup we performed above. Starting the Recovery of Database
Below are the steps which we will perform step by step to recover the Database.
Create the RDB
Create an RDB on which we will restore the Database backup. Make sure that when create the RDB the Exchange 2010 Node should be connected with physical name not via Virtual name if you are on a remote terminal. See the below SNAP for reference how to create the RDB:
Throw some light on the command which issued in step # 1
If you see the PRI- in the above SNAP this is the Server Name on which you are going to create the Recovery Database. The Server Name/Node Name should be the physical name of Node.
The "E" drive in the above SNAP is the Hard Disk Partition where the Database Backup will be Restore.
The Recovery\RDB are the folders where the Recovery Databases resides.
Verify that the Database is created
See the below SNAP which confirms you that the RDB is created.
Specify NetBackup Machine and Policy Type
Exchange 2010 Node should be connected with physical name not via Virtual name if you are on a remote terminal.
Open Backup, Archive and Restore and go to the Specify NetBackup Machine and Policy Type. Make sure that the Source Client for Restore should be virtual DAG name and the Destination Client for Restore should be the physical Exchange Node name on which you created the RDB
Select the Database which will be Restore
In this step we will select the Database which you are going to restore. See the below SNAP for reference:.
You may notice above that there are two DBs(DB1 and DB2) which backup we took in the above Backup Activity
Restore Mark Files
Before clicking the Start Restore button click on General TAB first and see the red highlighted DB1 name.
Make sure that you replaced the Database name. As the above example this DB1 name should be replaced with RDB which (RDB) we have created above.
Now see the below SNAP for reference how it will look like after replacing the name of DB1 to RDB. Make sure the the PATH is as it is.
Now you can click on Start Restore so that the Restore will start. To verify for the initial errors put a check on the Verbose in the View Status windows as shown below.
Note: But if you have a full and Differential backup need to restore and you want to restore one by one means first you want to restore Full then the Differential backup, so you have to un check the Commit After Last Backup Se is Restored check box from the Microsoft Exchange TAB when restore the Full backup and put the check when restore the Differential backup. For more/detail information see the below link too.
Now here the Backup and Restore procedure has been completed. I hope the above procedure I tried to explain will be very helpful and detailed to start the Backup and Restore in a simple Exchange 2010 HA environment.