cancel
Showing results for 
Search instead for 
Did you mean: 
Articles
cancel
Showing results for 
Search instead for 
Did you mean: 

Knowledge Base Articles

Netbackup for Sybase (step by step)

Netbackup provides a Sybase backup and restore solution that not all of us aware of. the attached document provides detailed instratuction on all the steps required for backup and restore of sybase database. Note ....     any feedback with mistakes...

Ahmed_Atef by Level 2
Partner
  • 5497 Views
  • 3 comments
  • 4 kudos

Netbackup BMR SRT creation issues

Issues with SRT creation:- Issue 1:- Environment:- Oralce Linux 6.7 as boot server Netbackup verson 7.6.1.1. ERROR:- 3PPCD CD ISO is giving the Permission denied error /nbu3pp/bmr-verchk.sh: Permission denied Error Message:-     The follo...

RamNagalla by Moderator
Partner    VIP    Certified
  • 1986 Views
  • 0 comments
  • 1 kudos

How to install Symantec System Recovery in a non-English version?

It is quite simple to run the installation of Symantec System Recovery (SSR) in a non-English version by starting it from "browse.exe" file. You just select the language you are interested in and continue the wizard. What if you, for some specific r...

w-d by Level 4
Employee Accredited Certified
  • 694 Views
  • 0 comments
  • 2 kudos

Discrepancy in the sizes of storage pools used for AIR replication

This could be encountered in NetBackup versions 7.1 and higher where Automated Image Replication (AIR) is used. All versions of PureDisk 6.6 and higher when used in a PDDO (PureDisk Deduplication Option) configuration may also be affected. A new Tech...

smurphy by Level 4
Employee Certified
  • 444 Views
  • 0 comments
  • 0 kudos

Symantec System Recovery 2013 - The status in the tray icon is blank, not able to see if backup/restore was successful or not. A green check mark in the tray icon is also not visible.

Issue Symantec System Recovery 2013 - The status in the tray icon is blank, not able to see if backup/restore was successful or not. A green check mark in the tray icon is also not visible.   Error Please check the logs which have been co...

MaXi_KiNg by Not applicable
Employee Accredited
  • 633 Views
  • 1 comments
  • 1 kudos

Problems Accessing WEBUI for Backup Exec 3600 Appliance

The article will take an overview about accessing WEBUI for BE appliance 3600 and R2. Appliance has four NIC Cards out of which NIC1/eth0 is normally used to configure the appliance and its recommended to disconnect the cable once the configuration i...

Nitin_P by Level 4
Employee Accredited
  • 789 Views
  • 0 comments
  • 1 kudos

Netbackup 7.x and media read errors - Are the basics done ?

This Article is only for Netbackup 7.5 version which uses Linux as operation system for example SLES 11 or RHEL. When you using the SLP or Vault Feature in NetBackup you can see a lot of issues like those: failed, media read error (85). cannot posit...

Speedy1205 by Level 4
Employee Accredited
  • 947 Views
  • 2 comments
  • 2 kudos

Troubleshoot NetBackup Status Code: 99

Permanent link   Problem:  How to troubleshoot NetBackup for NDMP Backup failures when status code: 99 (NDMP backup failure) is reported.  Includes logging instructions.   Error:  STATUS CODE: 99   Cause:  Status 99 in NDMP backups ...

smurphy by Level 4
Employee Certified
  • 3728 Views
  • 7 comments
  • 7 kudos

Steps to change Tape drive density name in Netbackup 7

Steps to change Tape drive density name in Netbackup 7 The below steps by step information on how to change a tape drive density name from HCART to HCART2/HCART3 Note: It is advisable that you stop all the ongoing backup?restoration before proceeding...

How ZFS Cache Impacts NBU Performance

Problem: Solaris 10 ZFS ARC Cache configured as default can gradually impact NetBackup performance at Memory level, forcing NBU to use a lot of Swap memory even when there are several Gig's of RAM "Available", in the following Solaris 10 server we i...

Omar_Villa by Level 6
Employee
  • 1652 Views
  • 4 comments
  • 7 kudos

Request for discussion: The NetBackup Common Topics page

Have you ever visited the Common Topics page for NetBackup Enterprise Server?  (I hope you have - its URL is in the signature of every reply I've left on the NetBackup forum!)  If you HAVEN'T, go ahead and click on this link right now...don't worry; ...

CRZ by Level 6
Employee Accredited Certified
  • 502 Views
  • 1 comments
  • 0 kudos

NetBackup Technical Information Updates: Deduplication FAQs

Speeding up deduplication Check here for new and updated technical articles (and videos) on NetBackup and NetBackup Appliances that have been vetted by a cross-functional content council of NBU product and technical support engineers.  The first art...

Virtual Machine Backup and Recovery: Five Critical Decisions

Who should read this white paper? This paper is intended for IT Architects, Backup and Recovery Administrators, and virtualization teams at medium size through Enterprise-scale organizations. Because of the outstanding economy, flexibility,and servic...

LOG Locations in Backup Exec

LOG Locations in Backup Exec:   Backup Exec Support Log (SymHelp): Default Directory: C:\Program Files\Symantec\Backup Exec Filename: <Servername>__<Date>__<Time>.sdbz Usage: Symantec Help (SymHelp) is a utility designed to quickly and efficiently di...

Sym-cr by Level 5
  • 24119 Views
  • 0 comments
  • 1 kudos

Tapes and Deduplication - Storage Lifecycle Policies

I wanted to share a data collection I did today, while working with IT Solutions, deciding the best approach on how we were going to continue sending our backups Offsite. We're running about 12000 jobs per weekend, 3000 of those going offsite on Tape...

Labels
Top Contributors