06-25-2014 10:35 PM
Hi,
After installation of VCS 6.0 in Sol10,I am unable to run even hastatus -sum command it says, command not found however, llttab shows the O/p as
bash-3.00# cat /etc/llttab
set-node papa
set-cluster 37074
link e1000g0 /dev/e1000g:0 - ether - -
link e1000g1 /dev/e1000g:1 - ether - -
link-lowpri e1000g2 /dev/e1000g:2 - ether - -
=====================================
bash-3.00# cat /etc/gabtab
/sbin/gabconfig -c -n1
============================
checked with pkginfo,
bash-3.00# pkginfo |grep vcs
system VRTSvcs Veritas Cluster Server by Symantec
system VRTSvcsag Veritas Cluster Server Bundled Agents by Symantec
system VRTSvcsea Veritas High Availability Enterprise Agents by Symantec
============================================================================
bash-3.00# df -h
Filesystem size used avail capacity Mounted on
/dev/dsk/c1t0d0s0 14G 2.3G 12G 17% /
/devices 0K 0K 0K 0% /devices
ctfs 0K 0K 0K 0% /system/contract
proc 0K 0K 0K 0% /proc
mnttab 0K 0K 0K 0% /etc/mnttab
swap 2.2G 1.1M 2.2G 1% /etc/svc/volatile
objfs 0K 0K 0K 0% /system/object
sharefs 0K 0K 0K 0% /etc/dfs/sharetab
/dev/dsk/c1t0d0s5 9.6G 4.3G 5.3G 45% /usr
/usr/lib/libc/libc_hwcap1.so.1
9.6G 4.3G 5.3G 45% /lib/libc.so.1
fd 0K 0K 0K 0% /dev/fd
/dev/dsk/c1t0d0s3 1.9G 93M 1.7G 5% /var
swap 2.2G 44K 2.2G 1% /tmp
swap 2.2G 32K 2.2G 1% /var/run
/dev/dsk/c1t0d0s4 2.9G 819M 2.0G 29% /opt
/dev/dsk/c1t0d0s6 103M 1.0M 92M 2% /temp
/dev/dsk/c1t0d0s7 18G 19M 18G 1% /export/home
/vol/dev/dsk/c0t0d0/sol_10_910_x86
2.0G 2.0G 0K 100% /cdrom/sol_10_910_x86
/dev/odm 0K 0K 0K 0% /dev/odm
/dev/vx/dsk/datadg/datavol
200M 103M 91M 54% /pictor
==========================================================
bash-3.00# vxdisk list
DEVICE TYPE DISK GROUP STATUS
disk_0 auto:none - - online invalid
disk_1 auto:none - - online invalid
disk_2 auto:cdsdisk datadg01 datadg online
disk_3 auto:cdsdisk datadg02 datadg online
PLease help..
06-26-2014 08:55 AM
hastatus command is in /opt/VRTSvcs/bin and there is a sym link in /opt/VRTS/bin, so add either of these to your path or specify complete path. I would advice adding /opt/VRTS/bin to your path:
export PATH=$PATH:/opt/VRTS/bin
Mike
06-27-2014 03:42 AM
'command not found' is a Unix error, saying that the current shell cannot find the command in your PATH variable.
You will find this recommendation in the sfha_install guide (Add the paths to your .profile to make it permanent):
Setting environment variables
Most of the commands used in the installation are in the /sbin or /usr/sbin
directory. Add these directories to your PATH environment variable as necessary.
After installation, SFHA commands are in /opt/VRTS/bin. SFHA manual pages
are stored in /opt/VRTS/man.
Add the following directories to your PATH and MANPATH environment variable:
■ If you are using Bourne or Korn shell (sh or ksh), enter the following:
$ PATH=$PATH:/usr/sbin:/opt/VRTS/bin
$ MANPATH=/usr/share/man:/opt/VRTS/man:$MANPATH
$ export PATH MANPATH
■ If you are using a C shell (csh or tcsh), enter the following:
% set path = ( $path /usr/sbin /opt/VRTS/bin )
% setenv MANPATH /usr/share/man:/opt/VRTS/man:$MANPATH
06-27-2014 06:11 AM
Thanks marianne.. got it and issue is resolved.