cancel
Showing results for 
Search instead for 
Did you mean: 
NetBackup

Discussion Posts

Subscribe to NBU notifications

In case you are not aware - you can subscribe to NBU notifications over here: https://sort.veritas.com/spec_doc Hopefully NBU 9 will be added to the list soon.

Marianne by Moderator
Partner    VIP    Accredited Certified
  • 5021 Views
  • 1 replies
  • 17 kudos

Resolved! How to confirm duplication jobs are optimized?

Hello, We are running a NB 6.5.6 environment, and have 2 DataDomain 880s, each in geographically distinct locale, under one NB domain. We are using OST (2.2) and DD Boost (4.9), and I've been reading about optimized duplication. Is there a way to dif...

LAToro by Level 4
  • 641 Views
  • 3 replies
  • 0 kudos

Netbackup Vault - no tapes to eject

Our tape library had a serious problem that required most of the internals to be replaced. Since then, the backup jobs run and backup to tape fine.  The vault job runs and the data is duplicated but it says there is no tapes to eject.  When we try to...

sensfan by Not applicable
  • 296 Views
  • 4 replies
  • 0 kudos

NetBackup 7 AD Granular Restore Cannot Browse in BAR

Hello,   I recently configured an Active Directory Granular Restore policy and all prerquisites using the Admin Guide. I can successfully take a backup (Exit Status 0), but when I go to do a restore I cannot browse further than ntds in Active Directo...

Sean_C_ by Level 3
Certified
  • 238 Views
  • 3 replies
  • 0 kudos

Netbackup 7.0 Admin Console Restore Report

Hello, I'm hoping someone can help me out. I performed a file restore from a Windows share directory about a month ago. Now, I need a report for that successful restore for a current SOX report. I've been looking for a while and google'ing with no su...

kilo by Not applicable
  • 193 Views
  • 1 replies
  • 0 kudos

Post NetBackup notifications to event log on client servers

Is it possible to post NetBackup job start/complete/fail notifications in the windows event log on client servers running a variety of Netbackup clients, mainly version 5.1? I may have read somewhere it is possible to get this information sent to the...

ricp by Level 4
  • 778 Views
  • 10 replies
  • 0 kudos

Resolved! Lost Storage Unit now Netback lost the backups on that Drive

Ok a couple of weeks ago My Snap storage device went down while I was backup up to it. I lost all my storage unit drives till I rebooted the snap. Now I have backups sitting on drives that Netbackup says aren't there, and it will not remove these fro...

Resolved! Media read error 85 importing phase 1 tapes

The customer lost the drfile and We're performing import phase 1 to  recovery the catalog backup tape. The problem is: We have 40 tapes and We just imported 13, the rest show: (media read error 85) and is imposible to perform import phase 2.   What c...

aduran by Level 3
Partner Accredited
  • 351 Views
  • 1 replies
  • 0 kudos

NO GRT in Lotus ???

I wonder why there is no GRT functionality in Lotus? Any idea.....

V4 by Level 6
Partner Accredited
  • 74 Views
  • 0 replies
  • 0 kudos

GRT Exchange Restore does not restore everything

I am consultant at a customer site performing a proof of concept for - NBU 7.0.1 - MS Exchange 2007 R2 - GRT backup to disk - Backup of Microsoft Information Store - Restore of Microsoft Information Store\vr01\vr01 is successful - Restore of singl...

FlashBackup-Windows policy restore error(2817)

HI, i am having a problem with restoration of an windows image from tape to vmware environment. log file attached below.      9/28/2011 4:42:46 PM - begin Restore 9/28/2011 4:42:49 PM - media R800L4 required 9/28/2011 4:42:49 PM - restoring image Win...

How to limit the number of duplication streams in AIR ?

I have two NetBackup 7.1.0.2 domains, and a replication between these domains by means of AIR. We can limit the bandwith used by one optimized duplication job, by means of the OPTDUP_BANDWITH parameter in pd.conf file... But NetBackup launch serveral...

Gdd by Level 6
Partner Accredited
  • 124 Views
  • 1 replies
  • 0 kudos

NBU 7 dedupe across master servers

I am new to NBU7 deduplication. I am working in an environment consisting of 6 master servers (seperate domains). Appreciate if you can confirm the following w.r.t NBU 7 deduplication: 1. Master server can be configured as the deduplication storage s...

dp_nash by Level 3
  • 399 Views
  • 3 replies
  • 0 kudos

Resolved! Disk pool informations using cli

    Hi, Please tell me if is there any command line option to show me all disk pools in NBU (disk pool names, space used, space available). Thanks a lot.    

Resolved! NetBackup 7.1 Windows Client Install - needs a diet

I'm working with our serverbuild team to come up with a "silentclient.cmd" file for 7.1 with 7.1.0.2 patch, that doesn't install all the extra componants we will never use on our Windows Clients.  Specifically, now do we keep it from installing the f...

NetBackup email notifications "send as"

I have been trying to configure my NetBackup 7.1 Unix server to send email notifications and have encountered a roadblock. The notifications get sent out as root@servername.domain.ds (.ds being the domain extension we use inhouse rather than .com). T...

NBU- BMR restoring a Windows server

I have a problem to restore an entire server using  Bare Metal Restore of NetBackup Environment: Master Server & Boot server (for Windows Servers):      Windows Server EE 2008 SP2 64 bits NetBackup  Server  version 7.0.1 Bare Metal Re...

mmeeggaann by Level 5
Partner Accredited
  • 778 Views
  • 6 replies
  • 1 kudos

How to retrieve images from tape

Hi Guys, I am just wondering if there is a way out for me here. I recently migrated our NBU6.5.4 master server  to NBU7.1 windowsR2. The catalog  backup of the NBU6.5.4 was done on wed afternoon, so we still have daily backup of wed and thursday ran ...

Yamoo by Level 3
  • 248 Views
  • 2 replies
  • 0 kudos

Hyper-V Backup

Hi, I have a problem with Virtual machines in Flash-backup-windows policy. The master server can connect with the Hyper-V host, but the virtual machines do not appear in the selection list tab. I saw in the event viewer that show me one error with th...