Subscribe to NBU notifications
In case you are not aware - you can subscribe to NBU notifications over here: https://sort.veritas.com/spec_doc Hopefully NBU 9 will be added to the list soon.
In case you are not aware - you can subscribe to NBU notifications over here: https://sort.veritas.com/spec_doc Hopefully NBU 9 will be added to the list soon.
i am working to enable client encrption in our backup environment and found a link https://www.veritas.com/support/en_US/article.TECH72130 in veritas support site. there are five steps to enable client encryption base on the document. How to config...
Hi All, We have a Netbackup 6.0 server installed on Windows server 2003, This server acts as both master and media server We use this server to take normal data and system backup on MSA storage and duplicate it on TApe To achieve the above task we...
Dear Expert, I just changed the tape and inventory this morning , the tape LT4012L5 is missing , but A00077 is appeared...(please refer the attached image) I am pretty sure A00077 is LT4012L5, but no idea why the Netbackup displayed the wrong...
Hi i am using Netbackup 7.0.1 with windows server 2003 and i am running our monthly backup and i get this error.. I change a lot of tapes.. Also the dailies backups and the monthly extrenal are running ok.. What should i do??
Hello, I need to backup a good no of clients in the DMZ servers.The media server has been setup in same DMZ LAN, however the Storage is in internal network.So as to get a good throughput is there a way to Minimize / Avoid the traffic through FW durin...
Hello , we are considering changing the current Backup Software from X to NetBackup , what are the most critical things to take into considerations , and i need to know how we'll be able to maintain the existing backups with long retention is there a...
Hi, OS : Windows 2003 Natbackup Version : 6.0 Issue : We see a job getting hung and blocks the schedule backups to start. The job shows as a catalog backup job. No particular timing of the job. Catalog backup policy schedule is from 06:00AM-04:00...
Hello, i try to realize some duplications on tape, but i receved this message : "netbackup the physical end of the tape has been reached" is there a way to show the physical end of the tapes ? Master server is Windows 2003. NBU : 7.0.1 ...
Hi Team, We are facing backup failure issue for MSSQL & Oracle Backups with error code 24 on linux media servers. whereas backup is working fine with unix media servers. Backup is failing immediately. Getting below error : bpbkar 10:54:39.284 [...
Hi, Can we import netbackup 7.1 images in netbackup 7.6.0.4. please confirm ?
Dear all expert, I am just a beginner at netbackup .. first at all thanks so much with you guys to save my life when reading my post.. I am usuing netbackup 7.1.0.4 and I just found a tape have problem after inventory. Therefore , I release the or...
Hi all Is that possible to limit the bandwith per job even if is running just one? I´m backing up a remote server with a microwave link which shares bandwith with the productive environment. We configured the policies to run only on working off h...
Hi; Trying to figure out if it is possible to setup netbackup using MSDP media servers to use OST drivers to Data Domain back-end? Is OST drivers on an MSDP even supported in this configuration ? thanks in advance
Hi All After running 2 minutes automatically drive is downing and getting below error. Please suggest me on this. 3/7/2016 11:34:47 AM - job 3463 was restarted as job 3467 3/7/2016 11:34:50 AM - started process bpbrm (6060) 3/7/2016 11:34:50 A...
Hi , I am new to the netbackup, any one guide me how to remove particualr backup directory from netbackup policy. where we dont want to keep this in backup rotation. also we dont want to remove the backups already done on tapes.
We are currently using the NetBackup Administration Console v7.1 I am a fresher and I have been given the following tasks to complete 1. I know how to perform this action For a specific client Report>Client backups>Choose client name>Set specifi...
Hi All, We have two NIC's on client one for production and another one for backup. We use backup interface for backup. but when I issued command bpclntcmd -pn on client host, It is pointing to production interface of client. Master server is reach...
Good day - Bonjour - Salam The status code 230 also occur, bat the policy has been removed. what van i for stopping tha status code appear. help please.
Good day - Bonjour - Salam The policy has been removed, but every day a status 230 occured. Your help please.
Hi All, I have one doubt. Recently I was working on bpclient command to update connnect options for one of the client server but it was giving me error "db_CLIENT() failed: no entity was found (227)bpclient: no entity was found (227)". After reviewi...