VCS discovery windows
Hello Experts, As part of a monitoring solution, we have been relying upon the presence of below registry keys to detect presence of a VCS on Windows, HKEY_LOCAL_MACHINE\SOFTWARE\VERITAS\VC HKEY_LOCAL_MACHINE\SOFTWARE\VERITAS\VCS\Base This however seems to be unreliable leading to false positives. I want an approach(could be a registry key/value) to detect a VCS with certinity on a Windows. Thank you! AshishI want to switch the application to minos2，but I cannot select the system
I want to switch the application to minos2，but I cannot select the system No system，why？ root@minos1(/)# hastatus -sum -- SYSTEM STATE -- System State Frozen A minos1 RUNNING 0 -- GROUP STATE -- Group System Probed AutoDisabled State B ClusterService minos1 Y N ONLINE B EMS minos1 Y N ONLINE B replication minos1 Y N ONLINE -- REMOTE CLUSTER STATE -- Cluster State N minos2 RUNNING -- REMOTE SYSTEM STATE -- cluster:system State Frozen O minos2:minos2 RUNNING 0
setting llt (low prio net) in a bond configured in a bridge
Hi, I want to set a low prio network over a bond which is part of a bridge. I have a cluster with two nodes. This is the network configuration (it is the same for both nodes): node 2: [root@node2 ]# cat /proc/version Linux version 2.6.32-504.el6.x86_64 (mockbuild@x86-023.build.eng.bos.redhat.com) (gcc version 4.4.7 20120313 (Red Hat 4.4.7-11) (GCC) ) #1 SMP Tue Sep 16 01:56:35 EDT 2014 [root@node2 ]# ifconfig | head -n 24 bond0 Link encap:Ethernet HWaddr 52:54:00:14:13:21 inet6 addr: fe80::5054:ff:fe14:1321/64 Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:761626 errors:0 dropped:0 overruns:0 frame:0 TX packets:605968 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1188025449 (1.1 GiB) TX bytes:582093867 (555.1 MiB) br0 Link encap:Ethernet HWaddr 52:54:00:14:13:21 inet addr:10.10.11.102 Bcast:10.10.11.255 Mask:255.255.255.0 inet6 addr: fe80::5054:ff:fe14:1321/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:49678 errors:0 dropped:0 overruns:0 frame:0 TX packets:50264 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:44061727 (42.0 MiB) TX bytes:28800387 (27.4 MiB) eth0 Link encap:Ethernet HWaddr 52:54:00:14:13:21 UP BROADCAST RUNNING PROMISC SLAVE MULTICAST MTU:1500 Metric:1 RX packets:761626 errors:0 dropped:0 overruns:0 frame:0 TX packets:605968 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1188025449 (1.1 GiB) TX bytes:582093867 (555.1 MiB) [root@node2 ]# brctl show bridge name bridge id STP enabled interfaces br0 8000.525400141321 no bond0 [root@node2 ]# cat /proc/net/bonding/bond0 Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009) Bonding Mode: fault-tolerance (active-backup) Primary Slave: None Currently Active Slave: eth0 MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Slave Interface: eth0 MII Status: up Speed: Unknown Duplex: Unknown Link Failure Count: 0 Permanent HW addr: 52:54:00:14:13:21 Slave queue ID: 0 node 1: [root@node1]# ifconfig | head -n 24 bond0 Link encap:Ethernet HWaddr 52:54:00:2E:6D:23 inet6 addr: fe80::5054:ff:fe2e:6d23/64 Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:816219 errors:0 dropped:0 overruns:0 frame:0 TX packets:668207 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1194971130 (1.1 GiB) TX bytes:607831273 (579.6 MiB) br0 Link encap:Ethernet HWaddr 52:54:00:2E:6D:23 inet addr:10.10.11.101 Bcast:10.10.11.255 Mask:255.255.255.0 inet6 addr: fe80::5054:ff:fe2e:6d23/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:813068 errors:0 dropped:0 overruns:0 frame:0 TX packets:640374 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1181039350 (1.0 GiB) TX bytes:604216197 (576.2 MiB) eth0 Link encap:Ethernet HWaddr 52:54:00:2E:6D:23 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:816219 errors:0 dropped:0 overruns:0 frame:0 TX packets:668207 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1194971130 (1.1 GiB) TX bytes:607831273 (579.6 MiB) [root@node1]# brctl show bridge name bridge id STP enabled interfaces br0 8000.5254002e6d23 no bond0 [root@node1 ]# cat /proc/net/bonding/bond0 Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009) Bonding Mode: fault-tolerance (active-backup) Primary Slave: None Currently Active Slave: eth0 MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Slave Interface: eth0 MII Status: up Speed: Unknown Duplex: Unknown Link Failure Count: 0 Permanent HW addr: 52:54:00:2e:6d:23 Slave queue ID: 0 the llt configuration files are the following: [root@node1 ]# cat /etc/llttab set-node node2 set-cluster 1042 link eth3 eth3-52:54:00:c3:a0:55 - ether - - link eth2 eth2-52:54:00:35:f6:a5 - ether - - link-lowpri bond0 bond0 - ether - - [root@node1 ]# cat /etc/llttab set-node node1 set-cluster 1042 link eth3 eth3-52:54:00:bc:9b:e5 - ether - - link eth2 eth2-52:54:00:31:fb:31 - ether - - link-lowpri bond0 bond0 - ether - - However this seems that is not working. When I check the llt status, the node thinks the interface is down in the other one. [root@node2 ]# lltstat -nvv | head LLT node information: Node State Link Status Address 0 node1 OPEN eth3 UP 52:54:00:BC:9B:E5 eth2 UP 52:54:00:31:FB:31 bond0 DOWN * 1 node2 OPEN eth3 UP 52:54:00:C3:A0:55 eth2 UP 52:54:00:35:F6:A5 bond0 UP 52:54:00:14:13:21 [root@node2 ]# lltstat -nvv | head LLT node information: Node State Link Status Address * 0 node1 OPEN eth3 UP 52:54:00:BC:9B:E5 eth2 UP 52:54:00:31:FB:31 bond0 UP 52:54:00:2E:6D:23 1 node2 OPEN eth3 UP 52:54:00:C3:A0:55 eth2 UP 52:54:00:35:F6:A5 bond0 DOWN Do you know if I have something worng? Is this a valid configuration? Thanks, Javier
deleting rlink that's having "secondary_config_err" flag
hello, in my VCS global cluster my ORAGrp resource group is partially online since my rvgres is offline, i am suspecting the issue in the below rlink. i am trying to dissociate thi rlink(below:rlk_sys1-DB-rep_DB_r) and dettach it in order to delete it but i am not able to succeed. below are some output from the system. root@sys2# vxprint -P Disk group: DBhrDG TY NAME ASSOC KSTATE LENGTH PLOFFS STATE TUTIL0 PUTIL0 rl rlk_sys1-DB-rep_DB_r DB_rvg CONNECT - - ACTIVE - - rl rlk_sys1-rep_DB-rvg DB-rvg ENABLED - - PAUSE - - root@sys2# vxrlink -g DBhrDG dis rlk_sys1-rep_DB-rvg VxVM VVR vxrlink ERROR V-5-1-3520 Rlink rlk_sys1-rep_DB-rvg can not be dissociated if it is attached root@sys2# vxrlink -g DBhrDG det rlk_sys1-rep_DB-rvg VxVM VVR vxrlink ERROR V-5-1-10128 Operation not allowed with attached rlinks root@sys2# vxedit -g DBhrDG rm rlk_sys1-rep_DB-rvg VxVM vxedit ERROR V-5-1-3540 Rlink rlk_sys1-rep_DB-rvg is not disabled, use -f flag root@sys2# vxedit -g DBhrDG -f rm rlk_sys1-rep_DB-rvg VxVM vxedit ERROR V-5-1-3541 Rlink rlk_sys1-rep_DB-rvg is not dissociated root@sys2# vxprint -Vl Disk group: DBhrDG Rvg: DB-rvg info: rid=0.1317 version=0 rvg_version=41 last_tag=11 state: state=CLEAN kernel=DISABLED assoc: datavols=(none) srl=(none) rlinks=rlk_sys1-rep_DB-rvg exports=(none) vsets=(none) att: rlinks=rlk_sys1-rep_DB-rvg flags: closed secondary disabled detached passthru logging device: minor=26012 bdev=343/26012 cdev=343/26012 path=/dev/vx/dsk/DBhrDG/DB-rvg perms: user=root group=root mode=0600 Rvg: DB_rvg info: rid=0.1386 version=13 rvg_version=41 last_tag=12 state: state=ACTIVE kernel=ENABLED assoc: datavols=sys1_DB_Process,sys1_DB_Script,... srl=sys1_DB_SRL rlinks=rlk_sys1-DB-rep_DB_r exports=(none) vsets=(none) att: rlinks=rlk_sys1-DB-rep_DB_r flags: closed secondary enabled attached logging device: minor=26014 bdev=343/26014 cdev=343/26014 path=/dev/vx/dsk/DBhrDG/DB_rvg perms: user=root group=root mode=0600 please advise regards