Ready; No idle devices are available
I'm new to Symantec Backup Exec as I've taken over the duties of someone else that left the company. The problem that I'm having is I can't get Backup Exec to backup anything, not to tape, not to a shared drive, etc.. Logically I would have thought the issue was that the previous employee had used his account for all Symantec functions, I was able to change his account information for all the services and the connection to the server. Everything appears to be fine, I'm able to do a Test Run without any problems but when I go to do a backup I don't receive any alerts I just get a message that says "Ready; No Idle devices are available". Same result no matter where I try to backup to. Anyone seen this before, have any suggestions of how I can fix it? We're using Backup Exec 2012 S1a. Thanks
BE 2012 - After migration, storage pools but no storage devices
Migrated our BE 2012 server using the steps in the article below. We moved from a Win2K8 R2 Enterprise OS to Win2K8 R2Standard OS for licensing reasons. Everything seemed to migrate successfully except for the storage devices which are simply network drives/shares. In the BE console on the new BE server, the storage pools, that were on the old BE server, are there and the properties of the storage pools show the related storage devices. The problem is that the storage devices do not show up as individual devices on the storage tab of the BE console, so I cannot edit the properties or even use them with the migrated backup jobs. I tried renaming the old BE server and taking it offline, then renaming the new BE server to the old BE server name, but I could not log into BE using the old or new name after that. I put the new name back into place so now I'm back at square one again. I thought about just configuring new storage devices with new names but I'm concerned about how that will affect my ability to restore existing backed up data that is on these drives. Ideally, I would like to get some help on how I can get this migrated BE server to recognize the storage devices again. https://support.symantec.com/en_US/article.TECH129826.html Thank You, RA
Backing up Active Directory: V-79-57344-33928 - (AD LDS) database was not found.
Hello, We have this error from time to time, but it usually fixes itself without any end user intervention. However I am getting this error three nights in a row now on one of our domain controllers. This started happening on Wed morning, and continued through Friday morning. In all three instances the error message in the log is: Job ended: Thursday, October 29, 2009 at 1:18:54 AM Completed status: Failed Final error: 0xe0008488 - Access is denied. Final error category: Security Errors For additional information regarding this error refer to link V-79-57344-33928 Errors Click an error below to locate it in the job log Backup- \\dc1.domain.com\System?State V-79-57344-33928 - Unable to complete the operation for the selected resource using the specified options. The Active Directory, Active Directory Application Mode (ADAM) or Active Directory Lightweight Directory Services (AD LDS) database was not found. So I checked the selections and under the server in question, I can see System State > Active Directory > C:_WINDOWS_NTDS, and this is all checked off. I did a test Resource Credentials for everything in this backup and it all returnedsuccessfulso I'm at a loss. Under Settings > Microsoft Active Directory for this job properties we have all three boxes checked (GRC, Consistency Check, Continue if Consistency check fails.) Backup method is greyed out, but says Full - Back up entire Active Directory. We are using Symantec Backup Exec 12.5 for Windows Servers Media Server Version 12.5 Rev 2213 Administration Console 12.5 Rev 2213 Desktop and Laptop Option: Version 3.1 Rev. 3.41.32a Installed updates: Service Pack 2 Hotfixes: 324947 317436 325647 319242 324012 326004 323894 324011 Thanks for the help, we really do appreciate it!
PowerVault 124T and Backup Exec 11d
Hi folks, I have been using a Dell PowerVault 124T with Backup Exec 11d for nearly three years and although the autoloader works well, I have had one issue that I have never been able to solve - or solve to what I believe to be satisfactory. :-) When our scheduled backupfills thefirst tape (LTO3) it will not run onto another tape without manually scanning the slot that the tapeis located- its as if Backup Exec/Autoloader doesn't see the tapes that are there. It will always start the backupandfind/use thetape in slot 1, but it will never look at the other slots for tapes unless I do the manual scan when I get the error message asking me to insert media. I have got around this by running a manual scheduled job that uses the bemcmd command that carries out an inventory of the specified slots before the backup runs - this then allows the backup to complete fine as it knows the tapes are there. I do have to be careful with this command though as if you set it to inventory all slots and the slots are not occupied with tapes, the inventory will fail and then the backup won't start. I guess my question is - should Backup Exec check the slots for tapes if you haven't run an inventory before a job starts? If so, is there any idea why I have the above problem when jobs go over the first tape? If not, then I know running an inventory before the job starts is the correct procedure - it just doesn't seem right as I would expect Backup Exec to do a scan of the slots before/during a job if it needs a tape. :-) Thanks for all your help Rob