SSR 2011 Symantec System Recovery Disk ISO download
I have SSR 2011 installed and would like to create a System Recovery disk, but i don't have the ISO. I know there's a download for that and I've seen a location for a 2013 version, but I assume I need a 2011 version. Where can I download one? Thanks, Rob13KViews1like15CommentsHow do I create a Custom Recovery Disk using the SSR 2013 Trial
I've just downloaded the SSR 2013 trial and want to create a bootable recovery disk. From what I can tell from the unavailable user guide and sparse help file, I need the to have a SSR disk or SSR recovery .iso in hand and neither was provided with the trial. Is there a way to proceed without them?3.3KViews1like31CommentsFormer Ghost 15 user - Getting trapped in the SSR 2013 Trial
A few days ago I had an issue with doing a system restore using Ghost 15. I went to that forum for help and learned that Symantec was going to discontinue Ghost and recommended users "check out" SSR 2013 with its free trial. I downloaded the free trial and eventually learned it would not install unless I first remove Ghost. That wasn't from anything that I saw when the SSR installation failed; that happened without any additional information. However, I did eventually find my way to this forum and a helpful Guru pointed out the issue and also that I could always re-install Ghost if I wasn't happy with SSR. I uninstalled Ghost, installed SSR, and started backing stuff up. Now, if one of the things you want to do is a full system restore (my primary interest)then you need a recovery disk. SSR will make a recovery disk for you and all you need to do is provide an activation key which you don't get with the trial version. No problem, as all I need to do is install Ghost. But I can't install Ghost until I uninstall SSR. And SSR WILL NOT UNINSTALL. Whenever I try to uninstall it there's an Error 2738 and something about a VBasic error. So now I have a trial verision of a program that I can't use and a paid for program I can no longer load. I guess it can all be fixed if I pay Symantec for an activation key for a program that I'm not sure I want in the hopes it will maybe allow me to upgrade to a latter version that can uninstall so I can install the program I uninstalled so I could evaluate the Free Trial. To put it another way, I may have to pay Symantec to I can remove their free software and load back the software I paid them for as well. And, even it it turns out there's a simple, and hopefully less expensive, way out of this I've still wasted a lot of time on what should be a free trial of a comercial product which appears to be more of an alpha test. (If I sound upset, it's because I really am)2.4KViews3likes12CommentsActive Directory Server (Windows 2003 R2) unable to boot after Installing Symantec System Recovery 2013
Hi Everyone, We successfully deploy SSR 2013 on Windows Server 2003 R2 but problem arised when we try to deploy it on an Active Directory Server. After successful installation, the server requires a reboot. But when we reboot it, the server failed to boot on Windows. What we do is to uninstall the SSR 2013 so that it can boot properly. We try other vesion of SSR like 2011 but same error occurs. The credential we used on installing SSR has an administrator rights. I would like to know if SSR 2013 and 2011 has compatibility problem on Active Directory and what we can do to fix it? Thanks in advance..:)2.1KViews0likes16CommentsInstall SSR 2013 R2 run failed
hi Symantec sensei Currently I'm struggling with installation of plug-ins, agents, SSR 2013 R2 with user interface on the end-point stations(200 stations) from SSR Management console (7.5.3153). Mostly it goes good, but some stations ignore the installation of “Package for Symantec System Recovery 2013 R2 with user interface”. In the agent history, it shows that “Install SSR…..Run failed”. I checked the obstacles, which could stop the installation – antivirus manipulations (exceptions, complete uninstall, etc.), win os firewall settings/rules (permit all in all directions), tried to Update Distribution Points, manually initiate the installation/downloading the package from Agent (CommonInstaller.exe. It starts for a sec and then disappears). PS: is it possible to install this package manually in offline mode? tried to find it, but without result Kindly ask You to help in this. The LOG file from Agent is attached. regardsSolved1.8KViews0likes8CommentsSymantec System recovery 2013
Hi , i'm very newer in SSR and i need to know some Knolage base: 1- SSR Server edition are just using for backuping servers? 2-SSR Desktop Edition are just used for backuping workstation? 3- in SSR Desktop Edition there is a management console for all workstation or pc are managed by their own console? 4-what should i take to save 10 pc without using a server ??Solved1.7KViews0likes11Commentshow to apply sp4 for BESR2010
Trying to resolve this known issue “Description: Error EBAB03F1: Operation aborted. Info 6C8F17E7: An automatic recovery point was not created because an earlier recovery point from the same job was still in progress. Details: Operation aborted” So Symantec came out with a Patch SP4 So I have been working with support for a month and a day waiting so some help I started with a call to support to install the patch with support help we used Symantec Installation Manager and started the process we got several error messages I guess this is normal is starts the install before downloading the update and error out them after the download it retries and continues Well I was closeing some backround windows and killed the upgrade so restated and erros products not istalled properly Support called back and we did repair and seemed ok but now can not select products to upgrade ? something wrong with font like there is no text so the case got escalated to next level support and has deen there since started the case Feb 03 2012 next level support got involved Feb 27 2012 well not really the message I got is “ACTION: researching possible causes of SIM display” It is now March 8 2012 how much long?? This is a simple patch for known problem Any body else have issues with Symantec Installation ManagerSolved1.6KViews0likes29Comments