BackupExec + S3 [A backup storage read/write error has occurred]
Hi, We have BackupExec 20.4 with StoreOnce on premise and use Amazon S3 with Storage Gateway for Virtual Tape Library (VTL). My jobs create backup onsite on StoreOnce and then they are pushed to the cloud via AWS S3 with a duplicate job. I only get this error from time to time and have already checked with my ISP, VPN Network team and opened a ticket with AWS. I ask if anyone can help me out with these failures that occur: Job ended: venerdì 19 giugno 2020 at 02:27:11 Completed status: Failed Final error: 0xe00084c7 - A backup storage read/write error has occurred.If the storage is tape based, this is usually caused by dirty read/write heads in the tape drive. Clean the tape drive, and then try the job again. If the problem persists, try a different tape. You may also need to check for problems with cables, termination, or other hardware issues.If the storage is disk based, check that the storage subsystem is functioning properly. Review any system logs or vendor specific logs associated with the storage to help determine the source of the problem. You may also want to check any vendor specific documentation for troubleshooting recommendations.If the storage is cloud based, check for network connection problems. Run the CloudConnect Optimizer to obtain a value for write connections that is suitable for your environment and use this value to run the failed backup job. Review cloud provider specific documentation to help determine the source of the problem. If the problem still persists, contact the cloud provider for further assistance.Final error category: Backup Media Errors Duplicate- VMVCB::\\XXXXX\VCGuestVm\(DC)XXXX(DC)\vm\XXXX An unknown error occurred on device "HPE StoreOnce:3".V-79-57344-33991 - A backup storage read/write error has occurred.If the storage is tape based, this is usually caused by dirty read/write heads in the tape drive. Clean the tape drive, and then try the job again. If the problem persists, try a different tape. You may also need to check for problems with cables, termination, or other hardware issues.If the storage is disk based, check that the storage subsystem is functioning properly. Review any system logs or vendor specific logs associated with the storage to help determine the source of the problem. You may also want to check any vendor specific documentation for troubleshooting recommendations.If the storage is cloud based, check for network connection problems. Run the CloudConnect Optimizer to obtain a value for write connections that is suitable for your environment and use this value to run the failed backup job. Review cloud provider specific documentation to help determine the source of the problem. If the problem still persists, contact the cloud provider for further assistance.V-79-57344-65072 - The connection to target system has been lost. Backup set canceled. I can't try cloudconnect optimizer because it's a iScSi connection. Any help would be great. Thank you, Federico PieracciniSolved3.5KViews0likes7Comments
Backup exec 2016 & Dell Compellent
Is there a way to backup Dell Compellent volumes, directly i did hear a while ago that you could do this by copying/mounting the volume/snapshot to the backup server and backing it up from there, i think it is all powershell scripting but wouldnt knwo where to start.1.5KViews0likes2Comments
Pause or Disable External Array?
Hi. I have a B2D setup where the array is JBOD Raid5 on a Dell PE510 PercH800. I need so swap out a dead drive in the array (VDrive). I will power off the array to do so but intend to keep the server running. Should I pause or disable the VDisk within BEX before taking it off line or will BEX automatically offline the VDrive when I power it down and online the drive when it is powered back on? Tnx954Views0likes1Comment
Moving Backup Sets to Another Disk Storage Location
We're replacing a NAS used for disk storage with a new larger one and I need to transfer the backup sets from the old to the new. I've read some posts stating that I need to run duplication jobs on all the backup sets to the new storage, but this seems awfully time consuming. Is it possible to robocopyeverything over including the .cfg and BEControl files? Or perhaps copy the .bkf files over an re-catalog them?Solved5.1KViews0likes2Comments
Backup Exec 15 does not consider overwritable media in storage capacity
Hi, I'm having a small issue with the Backup Exec storage screen. As shown below, the capacity of the tape library is reported as almost full: However, the media in the tape library is now outside of it's protection period and is marked as overwriteable: Should Backup Exec not see this overwritable media as available capacity? I should also mention that backups are running to tape correctly, it would just be nice to see usable capacity accurately on the storage screen, rather than having to drill down into the 'Slots' screen.Solved1.4KViews0likes2Comments
Backup exec 2016 & Dell Compellent
Is there a way to backup Dell Compellent volumes, directly i did hear a while ago that you could do this by copying/mounting the volume/snapshot to the backup server and backing it up from there, i think it is all powershell scripting but wouldnt knwo where to start.Pause or Disable External Array?
Hi. I have a B2D setup where the array is JBOD Raid5 on a Dell PE510 PercH800. I need so swap out a dead drive in the array (VDrive). I will power off the array to do so but intend to keep the server running. Should I pause or disable the VDisk within BEX before taking it off line or will BEX automatically offline the VDrive when I power it down and online the drive when it is powered back on? Tnx