Create second RDS using volumes from same disk group in Veritas volume replicator
Hi all, I have one query. I have one disk group with 5 volumes, which are more than 2 TB and are configured for replication. Now i want to add 2 more volumes in the RDS but it will resync all the volumes after adding these 2 volumes, so is it possible to make second RDS for only those 2 new volumes. Also can we use same IP for replication.5.5KViews0likes8CommentsHow do I verify my data size that will be replicated through VVR
I need to find a way to figure out the Mb/sec (Mb=Megabits) that will be replicated to my offsite and the pipe size I need in order to stay insync. I have been testing VVR and have all of my setting in place with everything working correctly. But with a 10Mb VPN internet pipe I have the line pegged at 10Mb all the time and am never able to catchup. When I looked at Performance monitor, Physical and Logical disks I am only generating about 4Mb/sec of disk writes which is what is being replicated the the offsite. Am I looking at the wrong data for my replication size needed? Is there a way to verify the Mb/sec that are going to be written the my offsite prior to starting VVR? NOTE: If you are having similar problems make sure to read the whole thread, there were mutliple solutions that were needed to verify and fix the problem of the data never catching up completely.Solved5.1KViews3likes17CommentsHow to check VVR replication status
Hi, one of our customers is using storage foundation 6.0 for Windows and they use VVR to replicate volumes from production site to dr site. The replication is in asynchronous mode. My question is: How to check VVR replication status? Is there a way to show the replication progress such as how many percentages have been replicated and/or how long it takes to complete the replication? Thanks in advance.Solved5KViews1like2Commentssecondary rvg unknown
Hello, I did the full sync and now the status is as below root@atmas1o:/ericsson/hagcs/log# vradmin -l printrvg Replicated Data Set: ossrvg Primary: HostName: pallini-ossrvg <localhost> RvgName: ossrvg DgName: ossdg datavol_cnt: 24 vset_cnt: 0 srl: oss_srl_vol RLinks: name=to_metamorphosi_ossrvg, detached=on, synchronous=off Secondary: HostName: metamorphosi-ossrvg RvgName: ossrvg DgName: ossdg datavol_cnt: 24 vset_cnt: 0 srl: oss_srl_vol RLinks: name=to_pallini_ossrvg, detached=on, synchronous=off Secondary: HostName: metamorphosi-ossrvg RvgName: ossrvg DgName: ossdg datavol_cnt: 24 vset_cnt: 0 srl: oss_srl_vol RLinks: name=to_pallini_ossrvg, detached=on, synchronous=off Config Errors: metamorphosi-ossrvg: unknown root@atmas1o:/ericsson/hagcs/log# vradmin -g ossdg repstatus ossrvg Replicated Data Set: ossrvg Primary: Host name: pallini-ossrvg RVG name: ossrvg DG name: ossdg RVG state: enabled for I/O Data volumes: 24 VSets: 0 SRL name: oss_srl_vol SRL size: 200.00 G Total secondaries: 1 Secondary: Host name: metamorphosi-ossrvg RVG name: ossrvg DG name: ossdg Data status: inconsistent Replication status: stopped (primary detached) Current mode: N/A Logging to: SRL Timestamp Information: N/A Config Errors: metamorphosi-ossrvg: unknown root@atmas1o:/ericsson/hagcs/log# root@atmas1o:/ericsson/hagcs/log# vxrlink -g ossdg status to_metamorphosi_ossrvg VxVM VVR vxrlink INFO V-5-1-3539 Rlink to_metamorphosi_ossrvg is not currently attached (STALE). You have new mail in /var/mail/root root@atmas1o:/ericsson/hagcs/log# Now if i start replication with below command, will there be any impact, as the primary is not buffering data as this status is there from last night. vradmin -g ossdg -s startrep ossrvgSolved4.8KViews1like33CommentsVolume replicator is not starting
Hi, Could you please guide me how to start Veritas Volume Replicator # vradmin -l printrvg VxVM VVR vradmin ERROR V-5-52-12 vradmind server not running on this system # /etc/init.d/vras-vradmind.sh start # vradmin -l printrvg VxVM VVR vradmin ERROR V-5-52-12 vradmind server not running on this system Regards, SatishSolved3.7KViews1like2Commentsvvr primary -primary configuration error
Dear support when i execute vradmin repstatus <rvg>the command reports the configuration error: "Primary-Primary configuration" the data now is on the secondary site and i haven't possibility to switch to the primary site with GCO tools Please your feedbackon this situation ThanksSolved3.4KViews1like1CommentCan not core dump because of system hangs
Hi, using these products : VRTS STORAGE FOUNDATION ENTERPRISE HA/DR FOR ORACLE RAC 5.1 UNX PER CPU TIER 2 STD LIC EXPRESS BAND S VRTS VOLUME REPLICATOR OPTION 5.1 UNX PER CPU TIER 2 STD LIC EXPRESS BAND S VRTS CLUSTER SERVER 5.1 UNX PER CPU TIER 2 STD LIC EXPRESS BAND S while system freezes / hangs completely -- no response from mouse, keyboard, anything; even can not take core dump to solve/fix the problem. is there a way to produce immediate dumps exactly on hang time? i.e. how can we set regular dumpings on every minute to catch the problem..3.4KViews0likes4Commentsvvr replication not ok .....need help to fix it
Hello, Replication is not happening , however RVG is enabled /active and Rlink is conect/active .... below are the details :--> -> vxprint -Pl Disk group: ossdg Rlink: to_sec_site_ossrvg info: timeout=500 packet_size=1452 rid=0.113591 latency_high_mark=10000 latency_low_mark=9950 bandwidth_limit=none state: state=ACTIVE synchronous=off latencyprot=off srlprot=autodcm assoc: rvg=ossrvg remote_host=sec_site-ossrvg IP_addr=10.52.214.68 port=4145 remote_dg=ossdg remote_dg_dgid=1444153050.96.secmas1o remote_rvg_version=30 remote_rlink=to_prisite_ossrvg remote_rlink_rid=0.1263 local_host=prisite-ossrvg IP_addr=10.52.214.67 port=4145 protocol: UDP/IP flags: write enabled attached consistent connected asynchronous dcm_logging -> vradmin -g ossdg repstatus ossrvg Replicated Data Set: ossrvg Primary: Host name: prisite-ossrvg RVG name: ossrvg DG name: ossdg RVG state: enabled for I/O Data volumes: 20 VSets: 0 SRL name: oss_srl_vol SRL size: 300.00 G Total secondaries: 1 Secondary: Host name: sec_site-ossrvg RVG name: ossrvg DG name: ossdg Data status: consistent, behind Replication status: logging to DCM (needs dcm resynchronization) Current mode: asynchronous Logging to: DCM (contains 61101728 Kbytes) (SRL protection logging) Timestamp Information: N/A -> vxrvg -g ossdg cplist ossrvg Name MBytes % Log Started/Completed ---- ------ ------ ----------------- point1 <Checkpoint overflowed> -> vxrlink -g ossdg status to_sec_site_ossrvg DCM is in use on rlink to_sec_site_ossrvg. DCM contains 61101728 Kbytes (19%) of the Data Volume(s). -> vxrlink -g ossdg stats to_sec_site_ossrvg Messages Errors Flow Control -------- ------ ------------ # Blocks RT(msec) Timeout Stream Memory Delays NW Bytes NW Delay Timeout 1 0 0 0 0 0 0 100000 1 10 primas1o{root} #: vxprint -PV Disk group: ossdg TY NAME ASSOC KSTATE LENGTH PLOFFS STATE TUTIL0 PUTIL0 rl to_sec_site_ossrvg ossrvg CONNECT - - ACTIVE - - rv ossrvg - ENABLED - - ACTIVE - - primas1o{root} #: vxrlink -g ossdg -i 5 status to_sec_site_ossrvg Mon Nov 30 17:24:01 2015 VxVM VVR vxrlink INFO V-5-1-12887 DCM is in use on rlink to_sec_site_ossrvg. DCM contains 61443008 Kbytes (19%) of the Data Volume(s). VxVM VVR vxrlink INFO V-5-1-12887 DCM is in use on rlink to_sec_site_ossrvg. DCM contains 61443008 Kbytes (19%) of the Data Volume(s). VxVM VVR vxrlink INFO V-5-1-12887 DCM is in use on rlink to_sec_site_ossrvg. DCM contains 61443040 Kbytes (19%) of the Data Volume(s). VxVM VVR vxrlink INFO V-5-1-12887 DCM is in use on rlink to_sec_site_ossrvg. DCM contains 61443232 Kbytes (19%) of the Data Volume(s). VxVM VVR vxrlink INFO V-5-1-12887 DCM is in use on rlink to_sec_site_ossrvg. DCM contains 61443232 Kbytes (19%) of the Data Volume(s). VxVM VVR vxrlink INFO V-5-1-12887 DCM is in use on rlink to_sec_site_ossrvg. DCM contains 61443264 Kbytes (19%) of the Data Volume(s). ^Cprimas1o{root} #: ===================================================================================================================== Secondary ======================================================= -> vxprint -Pl Disk group: ossdg Rlink: to_prisite_ossrvg info: timeout=500 packet_size=1452 rid=0.1263 latency_high_mark=10000 latency_low_mark=9950 bandwidth_limit=none state: state=ACTIVE synchronous=off latencyprot=off srlprot=autodcm assoc: rvg=ossrvg remote_host=prisite-ossrvg IP_addr=10.52.214.67 port=4145 remote_dg=ossdg remote_dg_dgid=1327928106.32.secmas1o remote_rvg_version=30 remote_rlink=to_sec_site_ossrvg remote_rlink_rid=0.113591 local_host=sec_site-ossrvg IP_addr=10.52.214.68 port=4145 protocol: UDP/IP flags: write enabled attached consistent connected -> vradmin -g ossdg repstatus ossrvg Replicated Data Set: ossrvg Primary: Host name: prisite-ossrvg RVG name: ossrvg DG name: ossdg RVG state: enabled for I/O Data volumes: 20 VSets: 0 SRL name: oss_srl_vol SRL size: 300.00 G Total secondaries: 1 Secondary: Host name: sec_site-ossrvg RVG name: ossrvg DG name: ossdg Data status: consistent, behind Replication status: logging to DCM (needs dcm resynchronization) Current mode: asynchronous Logging to: DCM (contains 61442560 Kbytes) (SRL protection logging) Timestamp Information: N/A -> vxrvg -g ossdg cplist ossrvg The cplist command can only be used on a primary rvg -> vxrlink -g ossdg status to_prisite_ossrvg The status command can only be used on a primary rlink -> vxrlink -g ossdg stats to_prisite_ossrvg Messages Errors Flow Control -------- ------ ------------ # Blocks RT(msec) Timeout Stream Memory Delays NW Bytes NW Delay Timeout 334089805 0 0 1927960 0 0 0 100000 1 10 Also, I ran the below command to check rlink bandwidth usgae and it is 0% utilised Cprimas1o{root} #: vrstat -R Mon Nov 30 17:43:49 2015 Replicated Data Set ossrvg: Data Status: sec_site-ossrvg: DCM contains 61543520 Kbytes. Network Statistics: Messages Errors Flow Control -------- ------ ------------ # Blocks RT(msec) Timeout Stream Memory Delays NW Bytes NW Delay Timeout primas1o 1 0 0 0 0 0 0 100000 1 10 Mon Nov 30 17:43:59 2015 Replicated Data Set ossrvg: Data Status: sec_site-ossrvg: DCM contains 61543552 Kbytes. Network Statistics: Messages Errors Flow Control -------- ------ ------------ # Blocks RT(msec) Timeout Stream Memory Delays NW Bytes NW Delay Timeout primas1o 0 0 0 0 0 0 0 100000 1 10 Bandwidth Utilization 0.00 Kbps. I am wondering if rlink in connect/active state then why its not replicating ? Regards SSolved3.3KViews0likes6CommentsVVR cross platform replication
The VVR 5.1 admin guide, in the "Cross-platform Data Sharing in VVR" section says: Refer to the Veritas Storage Foundation Cross-Platform Data SharingAdministrator’s Guide for more information. I have looked on SORT and I can only find a 5.0 version and this does not mention VVR as I believe cross platform replication has only been available since 5.1. Can anyone provide me an URL for this doc (and what search string/section I should use in SORT to find this). In SORT I searched for "cross platform replication" and I got several links all pointing to a very short document: Cross-platform data sharing Cross-platform data sharing (CDS) allows data to be serially shared among heterogeneous systems where each system has direct access to the physical devices that hold the data. This feature can be used only in conjunction with Veritas Volume Manager (VxVM). See theVeritas Storage Foundation Cross-Platform Data Sharing Administrator's Guide. But the last line is not a hyper link, so this did not help. Mike3.2KViews0likes3CommentsCluster GEO integration with VVR oracle database : steps order
I have 2 sites with the same config : 2 servers and storage. Each cluster have HA failover with Oracle database. I need to install Cluster GEO VVR to replicate Oracle data. My question is how to automate this configuration? Did i test first manually the VVR then I intagrate with the cluster Any Idea about the order and steps to automate this configuration Best regrads.Solved2.9KViews0likes9Comments