Windows Full system restore
Hello Experts, Original server crashed, we buil d new client server with same name and ip address and with same OS and patch version. Post that we installed same NBU client version. After installation we performed C:\ drive restore( completed successfully). Post C:\ drive restore we executed system state restore that too completed successfully After restore both ( C and system state) we rebooted the server but unfortunately server was not came UP, getting below error
Backup Exec 2010
Services will not start. See erroror message below. Any ideas? Start services on server: CHS-MAIN Starting Backup Exec Remote Agent for Windows Systems on CHS-MAIN. The service Backup Exec Remote Agent for Windows Systems is already running on CHS-MAIN. Starting Backup Exec Device & Media Service on CHS-MAIN. Error starting the service Backup Exec Device & Media Service on CHS-MAIN. The dependency service or group failed to start. Starting Backup Exec Server on CHS-MAIN. Error starting the service Backup Exec Server on CHS-MAIN. The dependency service or group failed to start. Starting Backup Exec Job Engine on CHS-MAIN. Error starting the service Backup Exec Job Engine on CHS-MAIN. The dependency service or group failed to start. Starting Backup Exec Agent Browser on CHS-MAIN. Error starting the service Backup Exec Agent Browser on CHS-MAIN. The dependency service or group failed to start. Starting Backup Exec DLO Administration Service on CHS-MAIN. Error starting the service Backup Exec DLO Administration Service on CHS-MAIN. The dependency service or group failed to start.Migrate off NetBackup 7.5.0.6 Windows 2008 over to NetBackup 10.2 on new hardware with Windows 2016
I have a server that is currently running NetBackup 7.5.0.6 on a Windows 2008 32 bit version. I need to upgrade the NetBackup application to the latest version on new hardware running Windows 2016 connected to a fibre channel connected Quantum Scalar i500 LTO 4 tape library. I am looking to understand what steps I need to take?
Netbackup Tape writing behaviour
Hello All, I have a question about tape retention. The question may be stupid and /i think i know the answer, but I am not sure. In a situation where netbackup is writing a frontend(client to tape) or SLP driven deduplication backup (disk to tape).. and for some reason the backup fails. What happens to the data that has already been written on the tape? Is it retained as per the policy schedule retention that is defined or is it discarded? Also what happens to such a tape where the backup that was writing to it failed before it could complete? Is there a way of identifying such tapes? Maybe erasing them and putting them i nthe scratch pool? Any help is fully appreciated. Kind Regards, Jay
Back up is slower than usual
We are using Symantec backup exec15 and when we run the back up, It is slower than usual, In job history, previous Job rateis 1000MB/min but now it became 500mb/min , please advise what to do to increase the performance. it was taking only 7 hours to do the process before but now it is taking 1 day already. Thanks in advance!Migration of Master server
Hi, I have a master server with this specification Phisical server Windows 2008 Netbackup 8.1.1 2 Disk pool connected by FC SAN I want to migrate to a new virtual server windows 2019. I have read this kb https://www.veritas.com/support/en_US/article.100022623 But i dont know if is possible this migration including this 2 disk pool (i should configure a hba passthrougth ) Regards
new appliance
hi, scenario: we already have 1 appliance (master media ) , console 8.0 is on Windows machine , now we install new appliance (flex) ( maser media ) and need to install the new master server console (9.1) on the same machine (Windows) (can i do that?) , move all policies and later on remove the old appliance. what is the best option to work with thanks in advancedSoftware Activation for Symantec Backup Exec 12.0
We are looking to get license keys for our software. We have the Software activation instructions but the resources are no longer available. Is there a way to retrieve the license keys? We have the reference code and activation code. Any help is greatly appreciated. Thank you.
How to update client netabckup from 7.7.2 to 8.1.1
Hello We have some trouble with EXchange backup on our machine the backup failed with error : ******** Couldnotfetchsnapshotmetadataorstatefiles (4207) ******** Il see that we should update the client to the same version as the master/media 8.1.1 we try to do that but we face the following error during the installation : *** 08-16-2021,09:33:27 : Action start 9:33:27: INSTALL. + 08-16-2021,09:33:27 : Action ended 9:33:27: INSTALL. Return value 3. *** Could you plaese advice Thank you in advance
