BackupExec arbeitet nicht mit 2. Laufwerk

1) Delete the library from BE

2) Shutdown both the media server and the tape library

3) power up the tape library.

4) power up the media server

5) in the Windows device manager, make sure that you can see the tape library as an Unknown Medium Changer with a Microsoft driver and the two tape drives.

6) in BE, use the Device Configuration Wizard to re-install the library and tape drives.

Tanks for the answer.

I deleted the 2 LTOs, reinstalled it with the windows driver. Then I started the wizard and now the Symantec Drivers are installed.

Now I have "IBM1" and "IBM2" instead of "IBM3" and "IBM4". But now there is a new problem. If i click on "Auftragsübersicht" I can read the following status: Bereit; Das angegebene Zielgerät auf dem lokalen Medienserver ist leer.

No job started and nothing happens. When I click on "Devices" (Geräte) I can see the following:

http://www.abload.de/img/zwischenablage0128xq.jpg

I hope you can help me again, because at the moment, there is no backup for us :(

Best regards

PS:

At the menu "Meldungen" I can see the following:

"Das Gerät \Device\Scsi\adpu16m1 hat innerhalb der Fehlerantwortzeiten nicht geantwortet"

"Der Wechselmediendienst kann die Bibliothek Tape0 nicht verwalten. Die Datenbank ist beschädigt" -> Ive seen this before, but it works always...

Did you follow the procedure that I gave earlier, including re-booting the server and the tape library?  If not, you should follow the procedure exactly!

If your Removable Storage Manager service is started, stop it.  It should not be started.  Ensure that it is not started.

Hey,

i did it like you said before. Deleted the Tabe Drives and the Library. But now it's the case, that i can read in the status "Bereit; Unbekannt". I read in a FAQ that you have to inventory the Libraries. I did this, but at ~97% der was an Error. That says that the Loader has a Problem. But when you look to the Scalar 100, there is no problem.

And now i can only make B2D and not to Tape. And that is very uncool, if you know what i mean ;)

I really have to find a solution and I hope you can help me with this problem!

Tank you for your help!

Try running the manufacturer's diagnostic utility against the library.  Stop all the BE services before hand and select the write test.  This is to eliminate hardware errors.

Under the Windows Device Manager, make sure that the tape library appears as an Unknown Medium Changer with a Microsoft driver.  If it is not, change the driver using he procedure below

How to uninstall the Original Equipment Manufacturer driver for the medium changer in a robotic library so as to make it "Unknown medium changer"

...if it shows Ready; Unknown, I've found 1 of 2 things work for me:

1. Restarting the BE services and then running the Device Configuration Wizard once more to install the Symantec drivers.

2. Opening up the selection list and making sure the jobs are targetting the correct drives/slots etc.

Thanks for your Help again.

@CraigV:

1. Restarting the BE services and then running the Device Configuration Wizard once more to install the Symantec drivers <- I did this, but there was nothing new at the end.

2. Opening up the selection list and making sure the jobs are targetting the correct drives/slots etc. <- I checked this, and is the right target as it was before my whole problems.

@pkh:

Try running the manufacturer's diagnostic utility against the library.  Stop all the BE services before hand and select the write test.  This is to eliminate hardware errors. <- I don't have a diagnostic Tool for our loader, that's the problem.

Under the Windows Device Manager, make sure that the tape library appears as an Unknown Medium Changer with a Microsoft driver.  If it is not, change the driver using he procedure below <- I did it, but nothing happend.

I made some Screenshots maybe you can see more things than me. This is from the Device Manager and the BE itself.

I REALLY hope, you can find the mistake, I don't know what to do..

http://www.abload.de/img/5nc8d.png
http://www.abload.de/img/15elv.png
http://www.abload.de/img/20dsb.png
http://www.abload.de/img/3if6p.png
http://www.abload.de/img/43c8i.png

Thanks guys, you're great!

Ok guys, i guess I got it.

The destination for the library was wrong. Now i fixed it and the first Tabe job started. I tried to change another one. When the first Backup is complete, I hope that he starts the next without any action of mine.

I will give a statement here, when I'm finished.

Thank you VERY much for your help!

Mmm...take all the tapes out, run a Scan/Inventory, and once it completes, put the tapes back. Then run a Scan/Inventory and see if this sorts things out.

Hey there,

it's me again.. I fixed the problem above. The solution was, that there were the wrong devices for the jobs.. But now i've another problem.

I got another  LTO and it's now in the loader, too. The same drivers, correct jumpers, new scsi cable. And it ALSO works, when i make an inventory. It loads the Tapes and unload it, too. But it doesn't work when a job wants to start. Just the old one works, not the new one.

Can you help me again?

Best regards

Michael