VXVM gives trouble in solaris11.2
Hi, I have installed VXVM6.0.1SF with trial version on Solaris11.2 inVMWare workstation. While installing the installer asked to set lwp_default and stksize to 0x8000. I have done it and completed installation successfully without any issue. After reboot also no issue. But if i give df -h command then immediately system going to kernel panic and starts rebooting and while booting it throws warning in lwp_default and stksize. Also i can see logs to run the vxkeyless setnone. This also done. Need any work around to fix this issue. Regards, vinothtvSolved1.3KViews1like1Comment
NFS cluster switchover getting failed from node1 to node2
I am facing issue when i am trying to switch the resource group from node1 to node2 and getting attached error for the nfs mount point. So can you please suggest the solution to this problem. Below is the nfs export and fstab file entry on node1 ,node2. [root@node1 ~]# cat /etc/exports /nfsshr01 *(rw,sync,no_root_squash) [root@node1 ~]# [root@node1 ~]# cat /etc/fstab /dev/VolGroup00/LogVol00 / ext3 defaults 1 1 LABEL=/boot /boot ext3 defaults 1 2 tmpfs /dev/shm tmpfs defaults 0 0 devpts /dev/pts devpts gid=5,mode=620 0 0 sysfs /sys sysfs defaults 0 0 proc /proc proc defaults 0 0 /dev/VolGroup00/LogVol01 swap swap defaults 0 0 # NOTE: When adding or modifying VxFS or VxVM entries, add '_netdev' # to the mount options to ensure the filesystems are mounted after VxVM and # VxFS have started. 192.168.56.121:/nfsshr01 /nfslock nfs defaults 0 0 [root@node1 ~]# [root@node2 ~]# cat /etc/fstab /dev/VolGroup00/LogVol00 / ext3 defaults 1 1 LABEL=/boot /boot ext3 defaults 1 2 tmpfs /dev/shm tmpfs defaults 0 0 devpts /dev/pts devpts gid=5,mode=620 0 0 sysfs /sys sysfs defaults 0 0 proc /proc proc defaults 0 0 /dev/VolGroup00/LogVol01 swap swap defaults 0 0 # NOTE: When adding or modifying VxFS or VxVM entries, add '_netdev' # to the mount options to ensure the filesystems are mounted after VxVM and # VxFS have started. 192.168.56.121:/nfsshr01 /nfslock nfs defaults 0 0 [root@node2 ~]# When trying to do manually getting below error for mount point under vcs. [root@node2 ~]# mount -t vxfs /dev/vx/dsk/nfsvdg01/nfsvol01 /nfsshr01 UX:vxfs mount.vxfs: ERROR: V-3-22168: Cannot open portal device: No such file or directory UX:vxfs mount.vxfs: ERROR: V-3-25255: mount.vxfs: You don't have a license to run this program [root@node2 ~]#Solved896Views0likes1CommentFlag status unknown
Hi All, I am trying to configure the nfs under VCS and getting the Flag status unknown error for NFSRestart service. So can you please suggest me the solution to this problem. Attached is the screenshot of the vcs console and main.cf configuration file. Thanks!!!!!!!!!!!! RavinderSolved2.7KViews1like5Comments
Collection from VRTSexplorer
Dear All I have some enviornments of SFHA and VCS installed on Linux and Solaris servers. I have output of VRTSexplorer logs for every system. As the VRTSexplorer contains almost everything collected, I wanted to know if is it possible to get the following output of these requirements 1. Which license and version and sub-version is installed on system? like for example if version 5.0 is installed which patch version is installed ? I want something except "vxlicrep" 2. If in the case of Replication, which file will give output of Bandwidth limit if it is configured. 3. If in the case of Replication, which file will give output of packet size if it is configured. Any suggession will be appreciated. Assume I just have VRTSexplorer and investigating logs and need to know the following. Regards2.2KViews0likes4Comments
corrupted veritas file system
Dear Support I am facing the below issue whenever running the fsck,please find the below details--- **************************************************************************************************** [10:40am] root@dwse: # /opt/VRTS/bin/fsck -F vxfs /dev/vx/rdsk/storagedg/vardws_vol UX:vxfs fsck: ERROR: V-3-20005: read of super-block on /dev/vx/rdsk/storagedg/vardws_vol failed: No such device or address file system check failure, aborting ... Exit 1 Exit 34 [10:43am] root@dwse: # /opt/VRTS/bin/fsck -F vxfs /dev/vx/rdsk/storagedg/varoptbgw_vol UX:vxfs fsck: ERROR: V-3-20005: read of super-block on /dev/vx/rdsk/storagedg/varoptbgw_vol failed: No such device or address file system check failure, aborting ... Exit 1 [10:44am] root@dwse: # ********************************************************************* Due to which volumes cannot be able to mount,kindly suggest what need to do/ regards....ArupSolved4.1KViews0likes8Comments
vxvm help required in
Hello friends, as shown below, one of the plex sybdata-01 has two subdisks like disk8-UR-003 as marked in bold I have never seen UR in subdisk what is it ? sybdata ossrvg ENABLED ACTIVE 387973120 SELECT - fsgen----------------- need to check pl sybdata-01 sybdata ENABLED ACTIVE 387973120 CONCAT - RW sd disk8-UR-003 sybdata-01 disk8 626688 118124544 0 c1t5006016139A02D78d6 ENA sd disk8-UR-002 sybdata-01 disk8 118755984 195734896 118124544 c1t5006016139A02D78d6 ENA sd disk5-06 sybdata-01 disk5 153264128 74113680 313859440 c1t5006016139A02D78d3 ENA pl sybdata-02 sybdata ENABLED ACTIVE 387973120 CONCAT - RW sd disk5mirr-03 sybdata-02 disk5mirr 51945472 367386624 0 c1t5006016139A02D78d10 ENA sd disk8mirr-02 sybdata-02 disk8mirr 98836480 20586496 367386624 c1t5006016139A02D78d13 ENA pl sybdata-03 sybdata ENABLED ACTIVE LOGONLY CONCAT - RW sd osssrldk1-21 sybdata-03 osssrldk1 1258296992 512 LOG c1t5006016146E02210d0 ENA pl sybdata-04 sybdata ENABLED ACTIVE LOGONLY CONCAT - RW sd osssrldk1m-21 sybdata-04 osssrldk1m 1258296992 512 LOG c1t5006016146E02210d1 ENASolved550Views0likes1Commentdata conversion activity SVM to VERITAS
Hi, I want perform SVM to VERITAS data conversion activity. means we have /dev/md/dsk/d30 as /oracle FS that same FS we have converted to VXVM as /dev/vx/dsk/oradg/oracle (encapsulation) without losing any single KB. can u tell me what are the stpes that we have to follws... Waiting 4 reply....Solved733Views0likes2Comments
Symantec Partner Accreditation Interview for Storage Foundation 6.0 for Unix
I have successfully passed Symantec Technical Specialist assessment of Veritas Storage Foundation 6.0 for Unix with a very good score. I had already passed both sales certifications (SSE & SSE+) of Storage Foundation 6.0 While preparing for STS assessment, I thoroughly went through all the training videos and the SF admin guide (almost 60%). Now Symantec has conducted my interview for technical accredition of my company as Specialist partner in Storage Management. Any suggestions regarding how to prepare for interview or which particular areas the interview will focus or some topic outlines that are important from interview perspective. Any suggestions or guidance will be highly appreciated. Thank You Atif Mehmood MalikSolved738Views0likes3Commentshagrp flush and probe
Hi , I was reading abt hagrp -flush when troubleshooting problems on service group and rsources and was not able to understand when we would be using this hagrp -flush and use of probe? I t would be great if somebody could explain with some example I tried to read abt Flushing a service group but was not able to understand perfectly. Occasionally, agents for the resources in a service group can appear to become suspended waiting for resources to be brought online or be taken offline.------------->in this scenario what would be the state of resource and service group. Generally, this condition occurs during initial configuration and testing because the required attributes for a resource are not defined properly or the underlying operating system resources are not prepared correctly. If it appears that a resource or group has become suspended while being brought online, you can flush the service group to enable corrective action.------------------------------------->what they mean by suspended ? Is it s state of a resource group. Flushing a service group stops VCS from attempting to bring resources online and clears any internal wait states. You can then check resources for configuration problems or underlying operating system configuration problems, and then attempt to bring resources back online.----------------------------------------> when we configure any resource with wrong attibutes and tries to bring onlineSolved1.5KViews0likes2Comments
Veritas Enterprise Administrator 3.2
Hi all, we are usingVeritas Enterprise Administrator 3.2 to sync/mirrow two sans. Unfortunately the collegue who has installed it is no more working here. Now i would like to see witch of both sans is at the moment the actice node but i can't find this point in the software. Can anybody help me with it? Thank you all!Solved900Views0likes3Comments
Collection from VRTSexplorer
Dear All I have some enviornments of SFHA and VCS installed on Linux and Solaris servers. I have output of VRTSexplorer logs for every system. As the VRTSexplorer contains almost everything collected, I wanted to know if is it possible to get the following output of these requirements 1. Which license and version and sub-version is installed on system? like for example if version 5.0 is installed which patch version is installed ? I want something except "vxlicrep" 2. If in the case of Replication, which file will give output of Bandwidth limit if it is configured. 3. If in the case of Replication, which file will give output of packet size if it is configured. Any suggession will be appreciated. Assume I just have VRTSexplorer and investigating logs and need to know the following. Regards