NBU 5220 Performance
We recently deployed a 5220 appliance into our environment as it was to be the savior in our battle against a backup window we were no longer able to meet. When we finally got it online and into our NBU environment the initial performance was great. The area we were to most benefit was with VMware backups. The data stores mounted directly to the appliance would allow direct access to the snapshots for a fast and efficient backup. Before this, we were performing client side backups so the impact on the hosts every night was significant as we tried backing up 600+ vms. The plan was to be able to move all Dev and test off-host backups to the middle of the day as the performance impact was minimal and the end result was an increased window to complete things. As we started with noon-time backups deduplication rates were high and so were the speeds. However, this performance gain was short lived, as we began increasing the load we suddenly saw performance drop to a point of concern. Backups were no longer speedy, 3500KB per second to 10,000KB. There are some that might pop to 24,000KB, but in a sample size of 15 as I write this, only one is showing 24,000. Now, I do have a few ideas. 1. We have a 72TB appliance, therefore, 2 disk trays, during the backups, the one disk tray is going crazy, all the lights are flashing and you can really see that it is working. However, the second tray is doing nothing. While you might see a blink here or there, it is almost nothing compared to the other disk tray. Is this to be expected? When we looked at the disk configuration, it shows concat, is this normal? 2. Too much data at once and we are simply burying the appliance. In reality, what sort of performance should I be able to expect from the appliance? 3. Relating to number 2, since we only have the one appliance right now while we wait to get the remote appliance in place, we are duping off to tape. This is running at the same time as a backup, so this means at the same time the appliance is writing a lot of data, it is also reading it back to tape. 4. We are overloading the data store so that read speed is bad from source to destination. We have fewer hosts,therefore, if we limit the jobs per host we limit the number of machines backing up at once (obviously). This means that backups take way long, so we removed the limit per host and just set a limit per data store. As we are new to it all, I am not sure what impact where, but again, I am trying to list any and all ideas from the start. 5. The appliance does not support multi-pathing, therefore, we only have a single path to the disk. Beyond that I am not sure, but this is something that doesnt help with the showcasing of the appliances to management at the moment. However, given the initial performance I am confident we can get back there.Solved3.2KViews4likes50CommentsAIR replication is failing
Hi All, I have master server on windows 2008 datacentre x64 and two 5230 Netbackup appliances. Main Site : One windows master server and one Netbackup 5230 appliance as media server DR site : One Netbackup 5230 appliace as media server. I am configuring AIR between main site windows master server and DR site Netbackup Appliance 5230 as master server. I have configured the aAIR as per standard configuration. I am facing an issue during replication. Please see the below replication job detail and help me. Thank you... ========================================================================================================== Logs : 9/10/2014 2:43:31 PM - requesting resource LCM_*Remote*Master*:msdp_sql_dc_to_dr_2_week 9/10/2014 2:43:31 PM - granted resource LCM_*Remote*Master*:msdp_sql_dc_to_dr_2_week 9/10/2014 2:43:31 PM - Info nbreplicate(pid=6296) Suspend window close behavior is not supported for nbreplicate 9/10/2014 2:43:31 PM - Info nbreplicate(pid=6296) window close behavior: Continue processing the current image 9/10/2014 2:43:31 PM - started process RUNCMD (6296) 9/10/2014 2:43:32 PM - requesting resource @aaaae 9/10/2014 2:43:32 PM - reserving resource @aaaae 9/10/2014 2:43:32 PM - reserved resource @aaaae 9/10/2014 2:43:32 PM - granted resource MediaID=@aaaae;DiskVolume=PureDiskVolume;DiskPool=dp_disk_dc-nbmedia01;Path=PureDiskVolume;StorageServer=dc-nbmedia01;MediaServer=dc-nbmedia01 9/10/2014 2:47:39 PM - Error nbreplicate(pid=6296) ReplicationJob::Replicate: Replication failed for backup id sqlf02_1410349007: media write error (84) 9/10/2014 2:47:39 PMReplicate failed for backup id sqlf02_1410349007 with status 84 9/10/2014 2:47:39 PM - end operation 9/10/2014 2:48:31 PM - Info bpdm(pid=206039) started 9/10/2014 2:48:31 PM - started process bpdm (206039) 9/10/2014 2:48:34 PM - Info dc-nbmedia01(pid=206039) StorageServer=PureDisk:dc-nbmedia01; Report=PDDO Stats for (dc-nbmedia01): scanned: 4 KB, CR sent: 1 KB, CR sent over FC: 0 KB, dedup: 75.0%, cache disabled 9/10/2014 2:48:35 PM - Info dc-nbmedia01(pid=206039) Using OpenStorage to replicate backup id sqlf02_1410349007, media id @aaaae, storage server dc-nbmedia01, disk volume PureDiskVolume 9/10/2014 2:48:35 PM - Info dc-nbmedia01(pid=206039) Replicating images to target storage server dr-nbmaster, disk volume PureDiskVolume 9/10/2014 2:52:35 PM - Critical bpdm(pid=206039) Storage Server Error: (Storage server: PureDisk:dc-nbmedia01) async_get_job_status: Replication started but failed to complete successfully: Error occured during replication. Look at the replication logs on the source storage server for more information. V-454-105 9/10/2014 2:52:35 PM - Error bpdm(pid=206039) wait failed: error 150 9/10/2014 2:52:35 PM - Error bpdm(pid=206039) <async> cancel failed: error 2060001: one or more invalid arguments 9/10/2014 2:52:35 PM - Error bpdm(pid=206039) copy cancel failed: error 174 9/10/2014 2:52:35 PM - Info dc-nbmedia01(pid=206039) StorageServer=PureDisk:dc-nbmedia01; Report=PDDO Stats for (dc-nbmedia01): scanned: 4 KB, CR sent: 0 KB, CR sent over FC: 0 KB, dedup: 100.0%, cache disabled no images were successfully processed(191)3.7KViews3likes4CommentsRegarding Appliance Health Check
Hi All, Is there any way we can configure appliance health report in hourly basis , I like to know how can I configure the report which send the appliance health status in 24 hours . I am not looking for sending email when any parts get faulty .Solved1.2KViews2likes2CommentsAfter upgrading appliance to 2.6.0.2 , backups fail intermittantly with error 24 and 14
Hi All, We recently upgraded on of our appliance from 2.5.3 to 2.6.0.2. It was a direct upgrade to 2.6.0.2 version. Since the upgrade backups are failing with error 24 and 14 mainly socket errors and we can see winsock error 10060 in bpbkar. The interesting thing is if we move the backups to the appliance which is not yet upgraded to 2.6.0.2 and is still at 2.5.3 level, the backup goes on fine. We have opened a case with Symantec and are still struggling for more than a week. Anyone of you had similar issues after upgrade. Kindly share and advise.Solved4.7KViews2likes36CommentsDetails on NBU appliances
Hi All, Hopping over from the BE forums :) I've got a requirement to start looking at the NBU appliances for a client of ours, and wanted to know how good they are, as well as models, Gartner report (if you have please share), usability, learnin curve for engineers etc. This would be to replace TSM... Thanks! CraigSolved683Views2likes3CommentsNetbackup Flashbackup or Agent based backups
Hi Guys Need some advice on backup solution regarding Netbackup . We have a 2TB volume on a file server and have installed Netbackup 2.6.0.3 running server 2012. the 2TB of data has loads of small files and also Enterprise vault place holders so windows journal can’t really kick in . We have accelerator and client dedupe enabled Using windows based backups it’s taking 23hrs to backup. Someone suggested using flash backups? We cannot use off host backups as the Media Server is a Netbackup 5230 appliance and does not support iSCSI Really need to bring the backup window down as I have a similar volume of 6TB to also migrate into Netbackup Kind Regards2KViews2likes7CommentsNetBackup Appliances and SCOM
Hi Just wondering if anybody was successfully monitoring Netbackup Appliances using SCOM 2012 R2. I tried using the SCOm Discovery to monitor one of ours, treating it just like a linux server, and received an error saying that the server refused to start a shell/command. Not necessarily after a resolution to the error, but would be interested to know whether anybody has got this sort of monitoring working. Thanks IanSolved1KViews1like2CommentsNetbackup Appliances is stucking over the night in the backup window
Hello, We are running netbackup master on a windows 2008 sp1 r2 server. In addition, all our backups go to 4 appliances that function as Media servers. Recently, we encountered long backup times. Sometimes, backups get stuck, causing other backup jobs not to start running and finnally cause them to abend with a 196 code. Please advise.Solved1.4KViews1like8CommentsSuddenly Differential copies of server files are extremately slow or hang
Hi there, I'm doing backups of my server file (Windows 2008 Enterprise) with Netbackup Appliance 5230. This server is a vmachine but the data disks are mapped as RAW so I've to use MS-Windows policy type. I've got 2 schedules, Full backup on weekend and Differential the rest of the week. These are the backup selections, each New streamare different vdisks in 2 SANs: Since yesterday, Monday, I'm having problems with the Differential backups in two ways: The first problem is, suddenly the backup task hangs in a folders with no errors or any message. I cancelled the task, it started again and several hours after hangs again in other folder of the same unit (N:\IT). these are the logs: first hang: 01/04/2014 0:02:00 - Info nbjm(pid=91943) starting backup job (jobid=2477) for client omgesfiles.global.com, policy Copia_Ficheros, schedule Diferencial 01/04/2014 0:02:00 - Info nbjm(pid=91943) requesting STANDARD_RESOURCE resources from RB for backup job (jobid=2477, request id:{15CE6746-B920-11E3-A05A-CC922E45814B}) 01/04/2014 0:02:00 - requesting resource stu_disk_omgesnetbu 01/04/2014 0:02:00 - requesting resource omgesnetbu.global.com.NBU_CLIENT.MAXJOBS.omgesfiles.global.com 01/04/2014 0:02:00 - requesting resource omgesnetbu.global.com.NBU_POLICY.MAXJOBS.Copia_Ficheros 01/04/2014 0:02:01 - granted resource omgesnetbu.global.com.NBU_CLIENT.MAXJOBS.omgesfiles.global.com 01/04/2014 0:02:01 - granted resource omgesnetbu.global.com.NBU_POLICY.MAXJOBS.Copia_Ficheros 01/04/2014 0:02:01 - granted resource MediaID=@aaaac;DiskVolume=PureDiskVolume;DiskPool=dp_disk_omgesnetbu;Path=PureDiskVolume;StorageServer=omgesnetbu;MediaServer=omgesnetbu 01/04/2014 0:02:01 - granted resource stu_disk_omgesnetbu 01/04/2014 0:02:02 - estimated 35059196 Kbytes needed 01/04/2014 0:02:02 - Info nbjm(pid=91943) started backup (backupid=omgesfiles.global.com_1396303322) job for client omgesfiles.global.com, policy Copia_Ficheros, schedule Diferencial on storage unit stu_disk_omgesnetbu 01/04/2014 0:02:02 - started process bpbrm (101231) 01/04/2014 0:02:03 - Info bpbrm(pid=101231) omgesfiles.global.com is the host to backup data from 01/04/2014 0:02:03 - Info bpbrm(pid=101231) reading file list for client 01/04/2014 0:02:04 - Info bpbrm(pid=101231) accelerator enabled 01/04/2014 0:02:10 - connecting 01/04/2014 0:02:11 - Info bpbrm(pid=101231) starting bpbkar on client 01/04/2014 0:02:11 - connected; connect time: 0:00:01 01/04/2014 0:02:15 - Info bpbkar(pid=4048) Backup started 01/04/2014 0:02:15 - Info bpbrm(pid=101231) bptm pid: 101270 01/04/2014 0:02:15 - Info bptm(pid=101270) start 01/04/2014 0:02:15 - Info bpbkar(pid=4048) change time comparison:<enabled> 01/04/2014 0:02:15 - Info bpbkar(pid=4048) accelerator enabled backup, archive bit processing:<disabled> 01/04/2014 0:02:16 - Info bptm(pid=101270) using 262144 data buffer size 01/04/2014 0:02:16 - Info bptm(pid=101270) using 30 data buffers 01/04/2014 0:02:16 - Info bptm(pid=101270) start backup 01/04/2014 0:02:16 - Info bpbkar(pid=4048) will attempt to use change journal data for <Q:\Datos HP> 01/04/2014 0:02:16 - Info bpbkar(pid=4048) will attempt to use change journal data for <Q:\Datos PHD> 01/04/2014 0:02:16 - Info bpbkar(pid=4048) will attempt to use change journal data for <N:\IT> 01/04/2014 0:02:16 - Info bpbkar(pid=4048) will attempt to use change journal data for <N:\OMDKB> 01/04/2014 0:02:16 - Info bpbkar(pid=4048) will attempt to use change journal data for <N:\SQLDATAOUT> 01/04/2014 0:02:16 - Info bpbkar(pid=4048) will attempt to use change journal data for <N:\Admon> 01/04/2014 0:02:16 - Info bpbkar(pid=4048) will attempt to use change journal data for <F:\Ignition> 01/04/2014 0:02:16 - Info bpbkar(pid=4048) will attempt to use change journal data for <G:\Insight> 01/04/2014 0:02:16 - Info bpbkar(pid=4048) will attempt to use change journal data for <R:\Datos> 01/04/2014 0:02:17 - Info bptm(pid=101270) backup child process is pid 101297 01/04/2014 0:02:17 - begin writing 01/04/2014 0:02:29 - Info bpbkar(pid=4048) not using change journal data for <Q:\Datos HP>: not configured for use 01/04/2014 0:02:29 - Info bpbkar(pid=4048) not using change journal data for enumeration for <Q:\Datos HP> but will use it for change detection 01/04/2014 0:15:57 - Info bpbkar(pid=4048) not using change journal data for <Q:\Datos PHD>: not configured for use 01/04/2014 0:15:57 - Info bpbkar(pid=4048) not using change journal data for enumeration for <Q:\Datos PHD> but will use it for change detection 01/04/2014 0:21:25 - Info bpbkar(pid=4048) 4999 entries sent to bpdbm 01/04/2014 0:47:28 - Info bpbkar(pid=4048) 9999 entries sent to bpdbm 01/04/2014 1:24:14 - Info bpbkar(pid=4048) 14999 entries sent to bpdbm 01/04/2014 1:43:57 - Info bpbkar(pid=4048) 19999 entries sent to bpdbm 01/04/2014 2:08:44 - Info bpbkar(pid=4048) not using change journal data for <N:\IT>: not configured for use 01/04/2014 2:08:44 - Info bpbkar(pid=4048) not using change journal data for enumeration for <N:\IT> but will use it for change detection 01/04/2014 2:12:53 - Info bpbkar(pid=4048) 24998 entries sent to bpdbm 01/04/2014 2:23:07 - Info bpbkar(pid=4048) 29998 entries sent to bpdbm 01/04/2014 2:31:11 - Info bpbkar(pid=4048) 34998 entries sent to bpdbm 01/04/2014 2:40:25 - Info bpbkar(pid=4048) 39998 entries sent to bpdbm 01/04/2014 17:31:18 - Error bptm(pid=101270) media manager terminated by parent process 01/04/2014 17:31:27 - Info omgesnetbu(pid=101270) StorageServer=PureDisk:omgesnetbu; Report=PDDO Stats for (omgesnetbu): scanned: 610712 KB, CR sent: 204697 KB, CR sent over FC: 0 KB, dedup: 66.5%, cache disabled 01/04/2014 17:31:28 - Info bpbkar(pid=4048) done. status: 150: termination requested by administrator 01/04/2014 17:31:28 - end writing; write time: 17:29:11 termination requested by administrator(150) 2nd hang: 01/04/2014 17:43:14 - Info nbjm(pid=91943) starting backup job (jobid=2559) for client omgesfiles.global.com, policy Copia_Ficheros, schedule Diferencial 01/04/2014 17:43:14 - estimated 35059196 Kbytes needed 01/04/2014 17:43:14 - Info nbjm(pid=91943) started backup (backupid=omgesfiles.global.com_1396366994) job for client omgesfiles.global.com, policy Copia_Ficheros, schedule Diferencial on storage unit stu_disk_omgesnetbu 01/04/2014 17:43:14 - started process bpbrm (39045) 01/04/2014 17:43:15 - Info bpbrm(pid=39045) omgesfiles.global.com is the host to backup data from 01/04/2014 17:43:15 - Info bpbrm(pid=39045) reading file list for client 01/04/2014 17:43:16 - Info bpbrm(pid=39045) accelerator enabled 01/04/2014 17:43:21 - connecting 01/04/2014 17:43:22 - Info bpbrm(pid=39045) starting bpbkar on client 01/04/2014 17:43:22 - connected; connect time: 0:00:01 01/04/2014 17:43:26 - Info bpbkar(pid=3868) Backup started 01/04/2014 17:43:26 - Info bpbrm(pid=39045) bptm pid: 39139 01/04/2014 17:43:26 - Info bpbkar(pid=3868) change time comparison:<enabled> 01/04/2014 17:43:26 - Info bpbkar(pid=3868) accelerator enabled backup, archive bit processing:<disabled> 01/04/2014 17:43:27 - Info bptm(pid=39139) start 01/04/2014 17:43:27 - Info bptm(pid=39139) using 262144 data buffer size 01/04/2014 17:43:27 - Info bptm(pid=39139) using 30 data buffers 01/04/2014 17:43:27 - Info bpbkar(pid=3868) will attempt to use change journal data for <Q:\Datos HP> 01/04/2014 17:43:27 - Info bpbkar(pid=3868) will attempt to use change journal data for <Q:\Datos PHD> 01/04/2014 17:43:27 - Info bpbkar(pid=3868) will attempt to use change journal data for <N:\IT> 01/04/2014 17:43:27 - Info bpbkar(pid=3868) will attempt to use change journal data for <N:\OMDKB> 01/04/2014 17:43:27 - Info bpbkar(pid=3868) will attempt to use change journal data for <N:\SQLDATAOUT> 01/04/2014 17:43:27 - Info bpbkar(pid=3868) will attempt to use change journal data for <N:\Admon> 01/04/2014 17:43:27 - Info bpbkar(pid=3868) will attempt to use change journal data for <F:\Ignition> 01/04/2014 17:43:27 - Info bpbkar(pid=3868) will attempt to use change journal data for <G:\Insight> 01/04/2014 17:43:27 - Info bpbkar(pid=3868) will attempt to use change journal data for <R:\Datos> 01/04/2014 17:43:28 - Info bptm(pid=39139) start backup 01/04/2014 17:43:29 - Info bptm(pid=39139) backup child process is pid 39147 01/04/2014 17:43:29 - begin writing 01/04/2014 17:43:40 - Info bpbkar(pid=3868) not using change journal data for <Q:\Datos HP>: not configured for use 01/04/2014 17:43:40 - Info bpbkar(pid=3868) not using change journal data for enumeration for <Q:\Datos HP> but will use it for change detection 01/04/2014 17:52:17 - Info bpbkar(pid=3868) not using change journal data for <Q:\Datos PHD>: not configured for use 01/04/2014 17:52:17 - Info bpbkar(pid=3868) not using change journal data for enumeration for <Q:\Datos PHD> but will use it for change detection 01/04/2014 17:56:24 - Info bpbkar(pid=3868) 4999 entries sent to bpdbm 01/04/2014 18:17:38 - Info bpbkar(pid=3868) 9999 entries sent to bpdbm 01/04/2014 18:48:16 - Info bpbkar(pid=3868) 14999 entries sent to bpdbm 01/04/2014 19:07:43 - Info bpbkar(pid=3868) 19999 entries sent to bpdbm 01/04/2014 19:28:36 - Info bpbkar(pid=3868) not using change journal data for <N:\IT>: not configured for use 01/04/2014 19:28:36 - Info bpbkar(pid=3868) not using change journal data for enumeration for <N:\IT> but will use it for change detection 01/04/2014 19:31:20 - Info bpbkar(pid=3868) 24998 entries sent to bpdbm 01/04/2014 19:41:12 - Info bpbkar(pid=3868) 29998 entries sent to bpdbm 01/04/2014 19:49:37 - Info bpbkar(pid=3868) 34998 entries sent to bpdbm 01/04/2014 19:58:56 - Info bpbkar(pid=3868) 39998 entries sent to bpdbm 01/04/2014 22:52:05 - Error bptm(pid=39139) media manager terminated by parent process 01/04/2014 22:52:16 - Info omgesnetbu(pid=39139) StorageServer=PureDisk:omgesnetbu; Report=PDDO Stats for (omgesnetbu): scanned: 1407408 KB, CR sent: 209592 KB, CR sent over FC: 0 KB, dedup: 85.1%, cache disabled 01/04/2014 22:52:21 - Info bpbkar(pid=3868) done. status: 150: termination requested by administrator 01/04/2014 22:52:21 - end writing; write time: 5:08:52 termination requested by administrator(150) The rest of the streams finished with no problems. But in thelast night differential copy the second stream (where N:/IT is) didn't even start and the first stream is still running (not hanged) for more than 11 hours! I'm using accelerator and the full backup worked last weekend (and it takes 12 hours) this is the log for the first stream: 02/04/2014 0:01:46 - Info nbjm(pid=91943) starting backup job (jobid=2569) for client omgesfiles.global.com, policy Copia_Ficheros, schedule Diferencial 02/04/2014 0:01:46 - estimated 48707354 Kbytes needed 02/04/2014 0:01:46 - Info nbjm(pid=91943) started backup (backupid=omgesfiles.global.com_1396389706) job for client omgesfiles.global.com, policy Copia_Ficheros, schedule Diferencial on storage unit stu_disk_omgesnetbu 02/04/2014 0:01:46 - started process bpbrm (108160) 02/04/2014 0:01:47 - Info bpbrm(pid=108160) omgesfiles.global.com is the host to backup data from 02/04/2014 0:01:47 - Info bpbrm(pid=108160) reading file list for client 02/04/2014 0:01:48 - Info bpbrm(pid=108160) accelerator enabled 02/04/2014 0:01:52 - connecting 02/04/2014 0:01:53 - Info bpbrm(pid=108160) starting bpbkar on client 02/04/2014 0:01:53 - connected; connect time: 0:00:01 02/04/2014 0:01:55 - Info bpbkar(pid=1944) Backup started 02/04/2014 0:01:55 - Info bpbrm(pid=108160) bptm pid: 108228 02/04/2014 0:01:55 - Info bpbkar(pid=1944) change time comparison:<enabled> 02/04/2014 0:01:55 - Info bpbkar(pid=1944) accelerator enabled backup, archive bit processing:<disabled> 02/04/2014 0:01:56 - Info bptm(pid=108228) start 02/04/2014 0:01:56 - Info bptm(pid=108228) using 262144 data buffer size 02/04/2014 0:01:56 - Info bptm(pid=108228) using 30 data buffers 02/04/2014 0:01:57 - Info bptm(pid=108228) start backup 02/04/2014 0:01:57 - Info bpbkar(pid=1944) will attempt to use change journal data for <O:\Digital> 02/04/2014 0:01:57 - Info bpbkar(pid=1944) will attempt to use change journal data for <P:\Datos> 02/04/2014 0:01:57 - Info bptm(pid=108228) backup child process is pid 108255 02/04/2014 0:01:57 - begin writing 02/04/2014 0:02:06 - Info bpbkar(pid=1944) not using change journal data for <O:\Digital>: not configured for use 02/04/2014 0:02:06 - Info bpbkar(pid=1944) not using change journal data for enumeration for <O:\Digital> but will use it for change detection 02/04/2014 0:12:46 - Info bpbkar(pid=1944) 4999 entries sent to bpdbm 02/04/2014 0:23:55 - Info bpbkar(pid=1944) 9999 entries sent to bpdbm 02/04/2014 0:38:19 - Info bpbkar(pid=1944) 14999 entries sent to bpdbm 02/04/2014 0:50:46 - Info bpbkar(pid=1944) 19999 entries sent to bpdbm 02/04/2014 1:00:38 - Info bpbkar(pid=1944) 24999 entries sent to bpdbm 02/04/2014 1:10:44 - Info bpbkar(pid=1944) 29999 entries sent to bpdbm 02/04/2014 1:16:40 - Info bpbkar(pid=1944) 34999 entries sent to bpdbm 02/04/2014 1:22:44 - Info bpbkar(pid=1944) 39999 entries sent to bpdbm 02/04/2014 1:30:32 - Info bpbkar(pid=1944) 44999 entries sent to bpdbm 02/04/2014 1:40:40 - Info bpbkar(pid=1944) 49999 entries sent to bpdbm 02/04/2014 1:54:25 - Info bpbkar(pid=1944) 54999 entries sent to bpdbm 02/04/2014 2:01:07 - Info bpbkar(pid=1944) 59999 entries sent to bpdbm 02/04/2014 2:05:43 - Info bpbkar(pid=1944) 64999 entries sent to bpdbm 02/04/2014 2:13:31 - Info bpbkar(pid=1944) 69999 entries sent to bpdbm 02/04/2014 2:21:24 - Info bpbkar(pid=1944) 74999 entries sent to bpdbm 02/04/2014 2:28:16 - Info bpbkar(pid=1944) 79999 entries sent to bpdbm 02/04/2014 2:34:58 - Info bpbkar(pid=1944) 84999 entries sent to bpdbm 02/04/2014 2:45:14 - Info bpbkar(pid=1944) 89999 entries sent to bpdbm 02/04/2014 3:03:00 - Info bpbkar(pid=1944) 94999 entries sent to bpdbm 02/04/2014 3:22:17 - Info bpbkar(pid=1944) 99999 entries sent to bpdbm 02/04/2014 3:25:57 - Info bpbkar(pid=1944) not using change journal data for <P:\Datos>: not configured for use 02/04/2014 3:25:57 - Info bpbkar(pid=1944) not using change journal data for enumeration for <P:\Datos> but will use it for change detection 02/04/2014 3:31:40 - Info bpbkar(pid=1944) 104998 entries sent to bpdbm 02/04/2014 3:47:40 - Info bpbkar(pid=1944) 109998 entries sent to bpdbm 02/04/2014 4:04:34 - Info bpbkar(pid=1944) 114998 entries sent to bpdbm 02/04/2014 4:25:56 - Info bpbkar(pid=1944) 119998 entries sent to bpdbm 02/04/2014 4:39:19 - Info bpbkar(pid=1944) 124998 entries sent to bpdbm 02/04/2014 4:55:08 - Info bpbkar(pid=1944) 129998 entries sent to bpdbm 02/04/2014 5:09:18 - Info bpbkar(pid=1944) 134998 entries sent to bpdbm 02/04/2014 5:18:20 - Info bpbkar(pid=1944) 139998 entries sent to bpdbm 02/04/2014 5:37:01 - Info bpbkar(pid=1944) 144998 entries sent to bpdbm 02/04/2014 6:00:47 - Info bpbkar(pid=1944) 149998 entries sent to bpdbm 02/04/2014 6:15:45 - Info bpbkar(pid=1944) 154998 entries sent to bpdbm 02/04/2014 6:27:52 - Info bpbkar(pid=1944) 159998 entries sent to bpdbm 02/04/2014 6:46:54 - Info bpbkar(pid=1944) 164998 entries sent to bpdbm 02/04/2014 7:06:21 - Info bpbkar(pid=1944) 169998 entries sent to bpdbm 02/04/2014 7:20:36 - Info bpbkar(pid=1944) 174998 entries sent to bpdbm 02/04/2014 7:30:10 - Info bpbkar(pid=1944) 179998 entries sent to bpdbm 02/04/2014 7:43:55 - Info bpbkar(pid=1944) 184998 entries sent to bpdbm 02/04/2014 8:00:54 - Info bpbkar(pid=1944) 189998 entries sent to bpdbm 02/04/2014 8:12:40 - Info bpbkar(pid=1944) 194998 entries sent to bpdbm 02/04/2014 8:35:25 - Info bpbkar(pid=1944) 199998 entries sent to bpdbm 02/04/2014 8:50:46 - Info bpbkar(pid=1944) 204998 entries sent to bpdbm 02/04/2014 8:57:50 - Info bpbkar(pid=1944) 209998 entries sent to bpdbm 02/04/2014 9:08:44 - Info bpbkar(pid=1944) 214998 entries sent to bpdbm 02/04/2014 9:30:23 - Info bpbkar(pid=1944) 219998 entries sent to bpdbm 02/04/2014 9:58:50 - Info bpbkar(pid=1944) 224998 entries sent to bpdbm 02/04/2014 10:25:48 - Info bpbkar(pid=1944) 229998 entries sent to bpdbm 02/04/2014 10:53:33 - Info bpbkar(pid=1944) 234998 entries sent to bpdbm Do you know where the problem could be? thanks for your help!587Views1like1Comment