07-05-2012 11:02 AM
Hello,
I am facing an issue, we have a robot control tape drive on netbackup 6.5.6 master, control host being the netbackup master server sesegx10.
This Tape drive is shared with other media servers, example sesegx08 and seprdu01.
The paths for sesegx10 and sesegx08 are ok but I cannot add a path for seprdu01 on the netbackup administration console giving the error: Drive address 8 is already occupied by a drive...(attached)
sesegx10: RHEL
sesegx09: RHEL
seprdu01: Solaris 10
Any help will be greatly appreciated. Can I send any relevant logs?
07-05-2012 11:05 AM
The error attached
07-05-2012 12:22 PM
Hi Noor,
Kindly ensure the drive 8 is accessable in media server( solaris 10) i,e device file.
In the information window which you pasted above says that the configuration details are not available because the drive is not configured on a host being scanned.
Issue the scan command and ensure that drive 8 is scanned and configure the same with tpautoconf comamnd.
07-06-2012 05:55 AM
Hello,
I ran the /usr/openv/volmgr/bin/scan command on the media server, but the tape is not detected.
Details below: the 2 drives i want to add being /dev/rmt/26cbn and /dev/rmt/27cbn
root@seprdu01.sagir.qc # luxadm disp /dev/rmt/27cbn
DEVICE PROPERTIES for tape: /dev/rmt/27cbn
Vendor: HP
Product ID: Ultrium 4-SCSI
Revision: H6AW
Serial Num: HU1149L0RG
Device Type: Tape device
Path(s):
/dev/rmt/27n
/devices/pci@43,700000/SUNW,qlc@0/fp@0,0/st@w20160013214436b6,0:n
LUN path port WWN: 20160013214436b6
Host controller port WWN: 2100001b32865264
Path status: Not Ready
root@seprdu01.sagir.qc # /usr/openv/volmgr/bin/scan | grep "Device Name"
Device Name : "/dev/rmt/4cbn"
Device Name : "/dev/rmt/12cbn"
Device Name : "/dev/rmt/3cbn"
Device Name : "/dev/rmt/11cbn"
Device Name : "/dev/rmt/10cbn"
Device Name : "/dev/rmt/2cbn"
Device Name : "/dev/rmt/0cbn"
Device Name : "/dev/sg/c0tw50022649f0806000l0"
Device Name : "/dev/rmt/9cbn"
Device Name : "/dev/rmt/8cbn"
Device Name : "/dev/rmt/7cbn"
Device Name : "/dev/rmt/6cbn"
Device Name : "/dev/rmt/5cbn"
Device Name : "/dev/rmt/1cbn"
Device Name : "/dev/rmt/22cbn"
Device Name : "/dev/rmt/21cbn"
Device Name : "/dev/rmt/20cbn"
Device Name : "/dev/rmt/19cbn"
Device Name : "/dev/rmt/18cbn"
Device Name : "/dev/rmt/25cbn"
Device Name : "/dev/rmt/24cbn"
Device Name : "/dev/rmt/17cbn"
Device Name : "/dev/rmt/16cbn"
Device Name : "/dev/rmt/15cbn"
Device Name : "/dev/rmt/14cbn"
Device Name : "/dev/rmt/13cbn"
Device Name : "/dev/rmt/23cbn"
root@seprdu01.sagir.qc # /usr/openv/volmgr/bin/sgscan
#
#WARNING: detected StorEdge Network Foundation connected devices not in
# SG configuration file:
#
# Device World Wide Port Name 50000972080a691d
# Device World Wide Port Name 50000972080a6925
# Device World Wide Port Name 20160013214436b6
# Device World Wide Port Name 50000972080a6918
# Device World Wide Port Name 20130013214436b6
# Device World Wide Port Name 50000972080a6910
#
# See /usr/openv/volmgr/NetBackup_DeviceConfig_Guide.txt chapter
# "Special configuration for "Sun StorEdge Network Foundation" HBA/Driver"
# for information on how to use sg.build and sg.install to
# configure these devices
#
/dev/sg/c0t0l31: Disk (/dev/rdsk/c2t0d31): "SUN Universal Xport"
/dev/sg/c0t4l0: Cdrom: "MATSHITADVD-RAM UJ-875S"
/dev/sg/c0tw20010013214436b6l0: Tape (/dev/rmt/1): "HP Ultrium 4-SCSI"
/dev/sg/c0tw20040013214436b6l0: Tape (/dev/rmt/23): "HP Ultrium 4-SCSI"
/dev/sg/c0tw20070013214436b6l0: Tape (/dev/rmt/0): "HP Ultrium 4-SCSI"
/dev/sg/c0tw200a0013214436b6l0: Tape (/dev/rmt/2): "HP Ultrium 4-SCSI"
/dev/sg/c0tw200d0013214436b6l0: Tape (/dev/rmt/24): "HP Ultrium 4-SCSI"
/dev/sg/c0tw20100013214436b6l0: Tape (/dev/rmt/25): "HP Ultrium 4-SCSI"
/dev/sg/c0tw50022649f0806000l0: Changer: "HP VLS"
/dev/sg/c0tw50022649f0806000l1: Tape (/dev/rmt/9): "HP Ultrium 4-SCSI"
/dev/sg/c0tw50022649f0806000l2: Tape (/dev/rmt/8): "HP Ultrium 4-SCSI"
/dev/sg/c0tw50022649f0806000l3: Tape (/dev/rmt/7): "HP Ultrium 4-SCSI"
/dev/sg/c0tw50022649f0806000l4: Tape (/dev/rmt/6): "HP Ultrium 4-SCSI"
/dev/sg/c0tw50022649f0806000l5: Tape (/dev/rmt/5): "HP Ultrium 4-SCSI"
/dev/sg/c0tw50022649f0806001l0: Tape (/dev/rmt/4): "HP Ultrium 4-SCSI"
/dev/sg/c0tw50022649f0806001l1: Tape (/dev/rmt/12): "HP Ultrium 4-SCSI"
/dev/sg/c0tw50022649f0806001l2: Tape (/dev/rmt/3): "HP Ultrium 4-SCSI"
/dev/sg/c0tw50022649f0806001l3: Tape (/dev/rmt/11): "HP Ultrium 4-SCSI"
/dev/sg/c0tw50022649f0806001l4: Tape (/dev/rmt/10): "HP Ultrium 4-SCSI"
/dev/sg/c0tw50022649f0806010l0: Tape (/dev/rmt/17): "HP Ultrium 4-SCSI"
/dev/sg/c0tw50022649f0806010l1: Tape (/dev/rmt/16): "HP Ultrium 4-SCSI"
/dev/sg/c0tw50022649f0806010l2: Tape (/dev/rmt/15): "HP Ultrium 4-SCSI"
/dev/sg/c0tw50022649f0806010l3: Tape (/dev/rmt/14): "HP Ultrium 4-SCSI"
/dev/sg/c0tw50022649f0806010l4: Tape (/dev/rmt/13): "HP Ultrium 4-SCSI"
/dev/sg/c0tw50022649f0806011l0: Tape (/dev/rmt/22): "HP Ultrium 4-SCSI"
/dev/sg/c0tw50022649f0806011l1: Tape (/dev/rmt/21): "HP Ultrium 4-SCSI"
/dev/sg/c0tw50022649f0806011l2: Tape (/dev/rmt/20): "HP Ultrium 4-SCSI"
/dev/sg/c0tw50022649f0806011l3: Tape (/dev/rmt/19): "HP Ultrium 4-SCSI"
/dev/sg/c0tw50022649f0806011l4: Tape (/dev/rmt/18): "HP Ultrium 4-SCSI"
/dev/sg/c1t1l31: Disk (/dev/rdsk/c5t1d31): "SUN Universal Xport"
root@seprdu01.sagir.qc # /usr/openv/volmgr/bin/scan | grep "26cbn"
root@seprdu01.sagir.qc # /usr/openv/volmgr/bin/scan | grep "27cbn"
root@seprdu01.sagir.qc # /usr/openv/volmgr/bin/tpautoconf -report_disc
=========== Missing Device or no local control path (Robot) ===========
Defined as robotic TLD(1)
Inquiry = "HP ESL E-Series 7.60"
Serial Number = US50839055
Robot Control Host = sesegx10
Drive = 4, Drive Name = HP.ULTRIUM4-SCSI.007, Serial Number = MXP1143FK0
Hosts configured for this device:
Host = seprdu01
07-06-2012 07:12 AM
If the tape drive IS visible at os level (eg luxadmin or cfgad,m -al -o show_FCP_dev )
then I would just rebuild the sg driver on the media sever.