06-20-2012 07:07 AM
hi,
i want to know how to load new tapes LTO4 to physical tape library the delete the data on this tapes to reuse them again or overwrite the data on this tape or erase the data on that tape :
i have :
Symantic Product Name: Symantec Netbackup
Product Version: 7.0.1
Operating System: HP-UX 11iv3
Solved! Go to Solution.
06-20-2012 11:58 PM
Did you look in the manyuals, the answes are all there ?
If you go into the robot inventory in the GUI and select the advanced options button
2 methods (use 1 or 2)
1)
As marianne mentioned, in the advanced options, you select the media type in the drop down, and the volumepool you wish the media to go into. This is found at the bottom of the 'Media Settings' tab. You need to unselect the 'Use barcode rules' tick box.
This works for one inventory only. If you rerun the inventory, you have to go back in and make these settings.
2)
Again in advanced options,
Goto barcode rules tab
Select new
Add the barcode tag. This has to be some part of the physical barcode that is unique to the tapes.
If my bardcodes are AA0001 etc , then I would use AA, as this would matcj all the tapes.
If other tapes are AB0001 etc ... then I would need an 'AB' barcode rule, as this would not match AA
I do not know if you can do this, you have not given informations as t what the barcodes are.
Select media type
Select volume pool you wish the tapes to go into
Martin
PS. Yes, delete the media (not eject) and rerun the inventory.
06-20-2012 07:19 AM
If the tapes are new, there is no need to overwrite anything, NetBackup will automatically label them and use them.
If the tapes have been previously used, NetBack will re-use them once the data on them has expired. There is no need to delete anything, they will just automatically be over written.
The only requirement is to physically load the tapes into the library and then run a library inventory from the GUI.
You do need to ensure that the tapes are given the correct density (eg. hcart, hcart2 etc ) and that this desity matches the tape drives.
For example, if the drive is density hcart2, the tapes must be the same(hcart2) in order for NBU to allow to be used with that drive.
This should be done by setting up barcode rules to match the barcode label on the tape, for example, if your barcodes are
AA1234L4
Then you would set a barcode rule to match AA = hcart2
That way, any tape starting AA will be given the hcart2 density.
This is all covered in the NetBackup Admin Guides part 1 and 2.
Here is a link to ALL the 7.5 manuals.
http://www.symantec.com/business/support/index?page=content&id=DOC5138&key=15143
Even if you are using 7.1 / 7.0 - the steps are the same, so this link should be fine.
However, the other documentation lionks can be found here .
http://www.symantec.com/business/support/index?page=landing&key=15143
If you follow the steps in the manuals, you will see how this is done.
Regards,
Martin
06-20-2012 07:24 AM
If there are no valid images in NBU catalogs for those tapes, they will automatically be overwritten.
No need to erase. You just need to inventory the library and ensure tapes are in correct backup pool(s) or in Scratch (if configured).
If your library has a MAP/CAP, you can put tapes in the these slots, close the MAP/CAP, select the robot in the Media section of GUI, right-click, Inventory. select Update volume configuration, then Empty media access port prior to update, then Start.
If you are unfamiliar with NBU media management, please read through Admin Guide I Section 3:
■ Chapter 7. Configuring robots and drives
■ Chapter 8. Configuring tape media
■ Chapter 9. Inventorying robots
06-20-2012 07:53 PM
Hi martin,
i do the following :
1-physically load the tapes into the library and then run a library inventory from the GUI.
2- and can see the tapes in inventory ?? ,,,, but cannot backup to them as :
library Tape drive type is : HCART
Media Type(density) is : DLT
so can i change Media Type is : DLT to HCART if so how to do that ??
and how to ensure that the tapes are given the correct density ??
And you said "This should be done by setting up barcode rules to match the barcode label on the tape, for example, if your barcodes are
AA1234L4
Then you would set a barcode rule to match AA = hcart2
That way, any tape starting AA will be given the hcart2 density.
"
How to do that ?can i do that in my case ????
library Tape drive type is : HCART
Media Type(density) is : DLT
thanks.
06-20-2012 08:43 PM
Rather use Media Settings Tab to change DEFAULT media type.
In Media type field, select the media type that matches your tape drives.
06-20-2012 11:42 PM
hi Marianne,
sorry how to change media type from DLT to HCART at GUI
06-20-2012 11:52 PM
hi marianne ,
i do all you said but after putting all new tapes with old configuration
now is it a must to eject these tapes again then insert them to take the update effect??
06-20-2012 11:58 PM
Did you look in the manyuals, the answes are all there ?
If you go into the robot inventory in the GUI and select the advanced options button
2 methods (use 1 or 2)
1)
As marianne mentioned, in the advanced options, you select the media type in the drop down, and the volumepool you wish the media to go into. This is found at the bottom of the 'Media Settings' tab. You need to unselect the 'Use barcode rules' tick box.
This works for one inventory only. If you rerun the inventory, you have to go back in and make these settings.
2)
Again in advanced options,
Goto barcode rules tab
Select new
Add the barcode tag. This has to be some part of the physical barcode that is unique to the tapes.
If my bardcodes are AA0001 etc , then I would use AA, as this would matcj all the tapes.
If other tapes are AB0001 etc ... then I would need an 'AB' barcode rule, as this would not match AA
I do not know if you can do this, you have not given informations as t what the barcodes are.
Select media type
Select volume pool you wish the tapes to go into
Martin
PS. Yes, delete the media (not eject) and rerun the inventory.
06-21-2012 12:03 AM
if it is a must to eject the media how to do that ??
i know that is done from media id > right click > eject volume from robot
06-21-2012 12:12 AM
Please read my posts carefully. I said to delete, not eject.
As per this post
https://www-secure.symantec.com/connect/forums/netbackup-basics-and-how-make-your-life-easier
It is expected that anyone on the forum (and that includes me) actually reads the manuals. Everything you are asking about is written down with step by step instructions in the guides. I am curious as to why you have not read these ?
Of course, if you do not understand something, post up the page and manual and question, and we will explain it to you. It IS expected that people make an effort, eg. read the manuals.
However, I will answer your question.
To delete the media, right click and select delete, not eject.
Please also not that in the above link, there is a list of minumum skills that I expect admins to have. We understand that you have to start somewhere (we have all been there) however, I would suggest you look through the list (in part (S) ) and undergo a training course in NBU to learn how to do these things.
It is not fair on you, if your employer expects you to do tasks such as your are doing with no training.
Martin
06-21-2012 12:20 AM
Hi Martin,
as i understand from your post i must delete the volumes (tape media) as follow media id > delete to take the effect of one of these two steps
1)
As marianne mentioned, in the advanced options, you select the media type in the drop down, and the volumepool you wish the media to go into. This is found at the bottom of the 'Media Settings' tab. You need to unselect the 'Use barcode rules' tick box.
This works for one inventory only. If you rerun the inventory, you have to go back in and make these settings.
2)
Again in advanced options,
Goto barcode rules tab
Select new
Add the barcode tag. This has to be some part of the physical barcode that is unique to the tapes.
If my bardcodes are AA0001 etc , then I would use AA, as this would matcj all the tapes.
If other tapes are AB0001 etc ... then I would need an 'AB' barcode rule, as this would not match AA
is that right ??
06-21-2012 12:24 AM
You could actually use vmchange -h <emm serevr> -new_mt <density> -m <media id> and change the density that way. This cannot be done from the GUI.
If you wish to do it from the GUI, then yes, you are correct, delete the media and follow one of the two steps.
Martin